Offroad-Express

phaedrus

If you're going to connect directly to the FTDI input then yes, just put a 390 ohm or thereabouts to ground at this point. If you look at the data output schematic of the 14CUX it is fed from 12v via a 500 ohm to the transistor collector, then a 100 ohm resistor out. Putting a 390 to ground will mea...

phaedrus

Had's (Nicegear) lead should be fine, as should most any other serial-usb interface. Inverting the signal is straightforward - just use an NPN transistor such as a BC549 with emitter to ground, collector to the RXD line (of the interface) and feed the base from the 14CUX via a resistive divider (wel...

phaedrus

It's been a while since I looked at this but if you found the FTDI board wouldn't config as needed I suppose I'd just invert the line using a bit of hardware - even a transistor would probably do.

Sorry I can't comment on the Trademe boards, I've never bought any of those.

phaedrus

Yep, the FTDI interface will work, and the connection detail is available on Github IIRC.

phaedrus

Sorry if I wasn't clear - they're completely separate vehicles and I'd just like to get a few bits for each one... I used to do stuff like that back in the day and you could certainly make an older machine look quite smart, but in this case I simply have an old Series and a new Defender. That said I...

phaedrus

Hi, as the title says i wonder if anyone knows of someone wrecking a post 2011 2.2TDCi Defender, pref a 110? I see a few have been written off around the place and I suppose someone must have bought them... Also, I'm looking for a few S3 bits in ChCh. If anyone has one they're parting out I'd be ple...

phaedrus

It's probably worth also checking your battery connections and leads - they may look ok but can sometimes have a high resistance that will cause just the problem you describe - and jumper leads can also be problematic. If the click you hear is from the starter area then it's likely to be either the ...

phaedrus

I have seen a Mistral with the rust problem, so it's worth checking, although I think it's a rarer issue than with the Terrano. Fortunately in this case I was looking at the vehicle for a friend and we passed that one by. He did however purchase another Mistral and is very happy with it. I've got on...

phaedrus

By all accounts they are prone to cylinder liner issues, the autos perhaps aren't the most reliable and you could have some problems with the air suspension. On the other hand they're a lot of vehicle for what you're likely to pay for one, they drive nicely (IMO) sound good and have a great tow rati...

phaedrus

If you're stuck I've got one in ChCh that I have as a spare for my various Nissans should I need it.

I'd need to get whatever it would cost me to replace should I need to at any stage. I'm not sure what that might be though, perhaps someone could help?

Cheers, P.

phaedrus

FWIW years ago I made up a fitting for the valve refacing machine to size down jag shims.

If you need a thinner shim and had a micrometer I see no reason why you couldn't do this even with an ordinary bench grinder.

Cheers, P.

phaedrus

Just to defend the places you've been to it's worth noting you may have experienced a catastrophic failure of your suspension joint, and that it may not have exhibited any particular symptoms when they looked at it. That said, fwiw, I purchased an optical wheel alignment unit around 30yrs ago and ha...

phaedrus

Where are you?

Assuming it's the same as a LJ50 I have a windscreen glass in ChCh (no frame though sorry).

Cheers, P.

phaedrus

Nick, I've never looked at the QD32 but it's possible they're similar to the TD27eti (perhaps someone else could confirm or otherwise?) as these appear to have problems not dissimilar to yours... If they are the same I did do a writeup on here of what I found in my TD27 'electronic' injection pump w...

phaedrus

I've got a body here in ChCh if you're up this way and want to take a look....

Cheers, P.

phaedrus

It might be worth adjusting the TPS, which in a D21 is on the top of the injector pump. Also check that it hasn't got a broken wire as it comes out of the sensor itself - I had one that did this and was able to repair it by cutting into the sensor a little and soldering on a new piece of wire. Other...

phaedrus

Phil, if it's a '96 then I imagine it has the electronic fuel pump? If so then they are known for playing up, unfortunately. I had intermittent shutdowns (amongst other things) with mine until it was sorted. That said I don't recall it refusing to start for such a long time - which could indicate so...

phaedrus

Remember that you've got a diff so it's possibly just one of the hubs, not both.

If you get stuck (sorry!) and can't get one I can probably find a good unit here, although I'd rather sell the whole vehicle...

Cheers, P.

phaedrus

Ok, well thanks for that, seems it's just what I'm looking for then; slow, old and needs winding up, just like me :-) I recall with my 2.8 4Runner that you had to slipstream and do all sorts of dubious things to get past someone but usually you could manage it somehow - I suspect, mind you, that the...

phaedrus

Thanks guys, and NJV6 I'd be interested to hear what you come up with on the transmission front. Certainly the one that was offered to me was a NZ new manual, I did see a small motor petrol one up for sale on TM a few months ago - really tidy and it went for about $5k or thereabouts I think but pers...

phaedrus

Hi guys, you'll normally find me over at the Nissan forum but I've got a query on 2.8 Prado's that I'm hoping you may help with. Years ago I was offered a (then) newish Prado, it was a '96 or '97 I think but it had the 2.8 Hilux normally aspirated motor. It also didn't have the body kit that most Pr...

phaedrus

Hello. I'm sorry I can't tell you about any specific common problems with this vehicle but certainly wiring and connectors would be the predominant issue with these sorts of things. Given that the wiring between the body and motor, and associated connectors, suffers the most movement and vibration t...

phaedrus

I've no specifc experience of this vehicle or motor but may be able to help.

I take it you still have the original sensor along with the one that's currently on the motor? For a start can you measure each one with a multimeter and tell us how many ohms they read?

P.

phaedrus

Hi Race. There should be a crankshaft position sensor (CPS) at the front of your motor. If you have a multimeter and are able to measure it should read about 1.6k ohms. In the case of the Terrano motor there are three leads coming from it, one of which is not needed. On my Mistral ('95, manual pump)...

phaedrus

I now have the auto working correctly so for anyone contemplating this mod I can confirm it's possible to do without much difficulty. If you change over the pump, and have an auto, you need to ensure the replacement mechanical pump has the TPS fitted to the throttle shaft at the top of the pump. If ...

phaedrus

...contd As the unit stands it is quite sturdy and operation of the pump along with information as to the precised location of the throttle shaft/sleeve is achieved without the use of any moving contacts (such as in a potentiometer) that could cause problems over time. Incidentaly I think the precis...

phaedrus

Covec injector pump operation. This pump appears to be an electro-mechanical pump with the main lower body of the pump assembly being entirely mechanical and the upper squarish cover assembly being the 'electronic' section. The upper section splits off from the lower mechanical unit fairly easily wi...

phaedrus

As the title implies this is about the later 'electronic' injector pumps that are commonly fitted to TD27's in Nissan Mistrals, Pathfinders and Terranos later than 1995 or so. I use the 'electronic' term somewhat lightly since in fact they turn out to be electro-mechanical and from what I can see th...

phaedrus

Well it's taken a while but I got the tacho working today. I'll be using the vehicle next week (I've had the Mistral on the road for the past 6 months) so thought I'd better sort a few things out with it. In order to make the tacho work it requires a pulse to be fed to the ECU from a sensor that is ...

phaedrus

Any change in your water level and/or is it getting hot? If so it's likely getting water where it shouldn't.

Injector pump isn't loose or too far retarded? Move top away from engine to advance if needed. Excessively retarded will smoke and have reduced power, usually hard to start as well.

P.

Search found 48 matches

Re: Rovergauge Cable

Re: Rovergauge Cable

Re: Rovergauge Cable

Re: Rovergauge Cable

Re: Anyone wrecking a post 2011 Defender?

Anyone wrecking a post 2011 Defender?

Re: Nissan Terrano starter issue

Re: mistrals...

Re: 2001 vogue rangey

Re: terreno 1991 outomatic gearbox wanted

Re: Valve Shims 1KZTE WTD

Re: Unsafe Ball Joint

Re: WTD: Suzuki LJ80 Windscreen

Re: Another QD32eti issue....

Re: 1991 Terrano Body needed

Re: TD27T auto - resistor on speed sensor?

Re: Terrano auto stalled, then starts and immediatly stalls.

Re: terrano auto hubs

Re: '96 or later Prado 2.8

Re: '96 or later Prado 2.8

'96 or later Prado 2.8

Re: Terrano rev counter swings wildly (or not at all)

Re: Nissan Rev Counter not working

Re: Terrano surging at low revs

Re: Terrano surging at low revs

Re: Nissan TD27 Zexel Covec 'Electronic' injector pumps

Re: Nissan TD27 Zexel Covec 'Electronic' injector pumps

Nissan TD27 Zexel Covec 'Electronic' injector pumps

Re: Terrano surging at low revs

Re: TD27 with ... the sickness!