Offroad-Express

HedgeBoar

On trademe: https://www.trademe.co.nz/Browse/Listing.aspx?id=1621251082 I do also have a whole lot of other Samurai/SJ413 bits for sale, such as: Power Steering Conversion Kit (inc. everything needed) 120A alternator conversion Strengthened rear axle housing, with sunken spring mounts, hilux wheel b...

HedgeBoar

Cheers PM sent.

HedgeBoar

Was going to rebuild my G13a but block is cracked. So after another one... interested in whole engine or block or anything in between. Cheers.

HedgeBoar

Second hand diffs for suzukis are a waste of time & money in my opinion. They aren't overy long lasting, so it's likely any second hand one you get will be on it's last legs. I went through 2 second hand ones in the space of a year before just rebuilding one. They both felt good when put in, pat...

HedgeBoar

Yes that's right -- I found a drawing of the chassis though so all sorted, cheers. The nominal dimension is 950mm.

HedgeBoar

Hey -- Could someone with a samurai rear axle housing hanging about tell me what the centre to centre distance between the spring plates is? I'm about to weld up my rear axle housing (whole lot of mods...) and I've lost my notes I took when I chopped it up... Centre to centre on my front leaf spring...

HedgeBoar

If you stand by what you have just stated, then according to your statement above, you would need to fit a 600amp alternator to winch for longer than 10 seconds. The alternator has absolutely nothing to do with winch performance during a pull and everything to do with battery recovery time between ...

HedgeBoar

Yes it would.... How much do you want for it?

HedgeBoar

This project is back on the top of the priority list again..... Any housings out there that need a home?

HedgeBoar

The problem is that your winch will pull in the order of 600 amps or more. Adding batteries helps for very short pulls, but even with two decent batteries you're talking a matter of tens of seconds 'til your alternator is the main limiting factor. I had a good run with my 110A falcon alternator -- a...

HedgeBoar

There will be no boom so long as you control your fuel and timing properly. Modest increases in horsepower (say 50-75%) are not going to cause engine internals much worry at all if you are not detonating, pre-igniting or getting ridiculous combustion temperatures. This is the main reason why I'd nev...

HedgeBoar

Update: Police found the truck somewhere in linwood, and it is now with it's rightful owner. Apparently it's pretty much intact, just missing all the tools etc. that were in it.

HedgeBoar

Mates 70 series shortie was stolen this arvo. Silver/grey. Has a unique Turbo 2B in it, side exhaust, unique sound.... "Ditch the Bitch, let's go hunting" sticker on the back. Taken from his driveway. EBY963 Photos: http://www.facebook.com/media/set/?set=a.2690645189902.146318.1369674430&a...

HedgeBoar

Hey,
I need an axle housing off a hilux -- any will do. I'm just after the flanges that bolt to the wheel bearing housings, so a bent or otherwise damaged housing would be perfect....

HedgeBoar

Well we didn't end up getting to the chasm track this time, we ended up having plenty of fun nearer our camp site (slab hut creek). FYI: When I tried to contact Ken on the phone number on the previous posts I found it was no longer his number. Luckily the guy I talked to knew the number I was lookin...

HedgeBoar

New brushes and bearings wont set you back much.... that's likely to be all you need.

HedgeBoar

i hope you are joking?? I wasn't meaning that they were nicely done, just that they still looked like a jimny as opposed to a jimny with a 410/413 body as the previous poster was talking about. I can't say I've ever had a close up look at one. Trepadors are the cheapest... by lots.... this is the o...

HedgeBoar

Is the info near the start of this thread regarding access still current? i.e.: cross Ken Fergersons Paddock (037323841) at the clarke end, and all public land at the staircase end?

HedgeBoar

The Jimny utes that Hollands have done look like they are a factory jimny flatdeck though... they don't look at all like a quick conversion has been done. I'd say the trepadors are a good choice -- I have a set of the 31"s on my samurai and they go very well in both boggy stuff and wet grass etc.

HedgeBoar

If it hasn't been driven with play in the pinion shaft, the gear set is probably OK. If you end up replacing it, I might be interested in buying it off you -- as you say, the samurai ones are mildly interesting to get your hands on, and I tend to be hard on them!

HedgeBoar

Got this conversion all finished and running. Ended up machining another groove in the inner pulley (the one that runs the alternator and water pump) so it is now 4 groove instead of the 3 groove that was original..... The 3 groove belt would have been touch and go with the 110A alternator. Luckily ...

HedgeBoar

There is a crown and pinion on trademe for cheap at the moment if you want to rebuild yours -- I bought his front one for a spare, he still has the rear on there.

HedgeBoar

Looking for an SC12 supercharger at a reasonable price. I would consider one in any condition.

HedgeBoar

Got a water pump and pulley this weekend. The water pump pulley from an 8 Valve vitara (found thanks to Falsgrave auto spares) works with the standard SJ413/samurai water pump, and aligns perfectly with the barina crank pulley (the inner one). I've got an alternator pulley off a nissan V8 that align...

HedgeBoar

That'd be great if you could compare them, cheers. I went into hollands suzuki yesterday, they had two different ones -- one was about 80mm from gasket face to hub face, the other 72mm. The 72mm had extra bits on the gasket face though and was missing a tapped hole, so may not be of much use.... The...

HedgeBoar

Update: Seems there are three water pumps that will fit on the G13A: -The one I have, which fits on the sj413/samurai with the clutch driven fan. 40mm PCD for the pulley studs. -One that fits on G13BA samurais with no engine driven fan and G13A swifts. 60mm PCD for the pulley studs. -Another one tha...

HedgeBoar

Valve clearances could be wrong..... It would make the noise all the time if that is the case, but as you say, you may not be able to hear it while driving due to road noise....

HedgeBoar

In relation to my thread on converting my samurtai to multi-V (http://www.offroadexpress.co.nz/Forums/viewtopic.php?f=23&t=24268) I'd like to see some photos of the front of some vitara engines to get an idea of what water pump pulleys might work. I'm looking for pics of both 8 and 16 valve engi...

HedgeBoar

Will do mate. At this stage I'm thinking I may need to get an extra groove machined in the pulley I got off UBZ. Currently it has one 3 rib and one four rib pulley. I'll need a four rib to run the supercharger (sc12) and the other one will run the alt, water pump, and power steering pump -- I think ...

HedgeBoar

Cheers Guys.

UBZ, I have a PS pump & tensioner, but I would be interested in the crank pulley if you'd be willing to sell it seperately...

Search found 100 matches

Suzuki Wheels & Tyre set & other bits for sale

Re: Wanted: Suzuki g13 engine or block

Wanted: Suzuki g13 engine or block

Re: SJ 413 Diff head

Re: Quick question -- Samurai Axle housing

Quick question -- Samurai Axle housing

Re: Winches and alternators?

Re: WANTED: Hilux rear axle housing - bent, broken OK

Re: WANTED: Hilux rear axle housing - bent, broken OK

Re: Winches and alternators?

Re: Supercharger GSXR set up

Re: Stolen 70 series Cruiser in CHCH Wed 16th Nov

Stolen 70 series Cruiser in CHCH Wed 16th Nov

WANTED: Hilux rear axle housing - bent, broken OK

Re: bulletproof Chasm track re opened

Re: FJ70 alternator recon?

Re: Brand new Sami's now available (kind of)

Re: bulletproof Chasm track re opened

Re: Brand new Sami's now available (kind of)

Re: After a Samurai Rear Diff

Re: Multi-V conversion on Samurai G13a

Re: After a Samurai Rear Diff

WANTED: SC12 Supercharger

Re: Multi-V conversion on Samurai G13a

Re: Multi-V conversion on Samurai G13a

Re: Multi-V conversion on Samurai G13a

Re: help! g16a sounds like a DIESEL

Wanted: Photos of Vitara belt setups

Re: Multi-V conversion on Samurai G13a

Re: Multi-V conversion on Samurai G13a