Instead of emailing it out...
Here is a link

http://www.mediafire.com/file/4lnykdwli ... et_XD9.pdf

Will leave it up for a few weeks..

Cheers
Calvin

Hey Nick I have a Warn service manual for the Xd9000...in pdf (5MB). Can email it to you....Shows you how to pull down and assemble again. The motor can be tested at a motor rewinder..... The warn brushes are expensive.... I stuffed mine up last year and replaced it with a ComeUp motor. Had to do so...

And here is how they recovered it....

http://www.youtube.com/watch?v=i26Ho-0UOJs

Calvin

He gave it a good go....
Needed lockers...
Pity about the end.

http://www.youtube.com/watch?v=_mKm9TxJ_MI

Cheers
Calvin

Cant seem to get two photos up on one post.
Here is the probe.

Photos of thermocouple and gauge... Gauge just sitting on dash, will mount properly later. Drilled with engine running. Put grease on tap, and cleaned and changed every turn. Then ran with hole open.... Also put high temp gease / thread lube on stainless fittings on assemble. Stops it picking up thr...

Put probe in maifold today... Easy as with a right angle battery drill. Taped the thread..... Currently it is jury rigged in the cab... Looks the part.....Will go for a drive over the weekend.. Question.. What temps do you normally expect to see.... And what is the max temp I want to keep under? Che...

Have you been off road and knocked the fuel line closer to a heat source....Vapour lock??

Or as already discussed....Air leak in fuel system...

Cheers
Calvin

Thanks 2MEKE

Nice photo...Will try and put mine in the junction before it heads down to the turbo just above the flange.
Gunna be a B@T$H to drill but workable.
And in car....

Cheers
Calvin

EGT unit arrived in the mail today. Only 6 days from the USA. Looks the part and the display unit is compact. Will fit up this weekend all going well.... To use ebay, set up an account (register) and I have linked / used Pay Pal......(register with Paypal) Pay pal uses your credit card to charge / p...

I use a Navman N40i which I have unlocked.... It now runs both the original Navman street maps. And also Ozi Explorer... And calibrated maps topo maps (free except for download data usage) ... Plus can run other applications. Still gets signals in forests.... Cost was about $250 for used navman........

From memory the factory set up in KZJ70 (Sqaure Prado) series wont allow you to lock the lockers unless you are in 4wd and low range.
There are tricks to fool the control box.
Also you must be going 5k's or less.
I suspect the 80 series factory set up could be similar.

Cheers
Calvin

Johnno Thanks for the info.... Would like to see the photo's. Heath Here is the link where I purchased the gauge and thermocouple. http://cgi.ebay.com/ws/eBayISAPI.dll?ViewItem&item=200421204953 All up its $145 NZ inc shipping. I looked at various analouge gauages here in NZ but they want far to...

I am not sure if this is the place but I cannot complaine about the prices...Best I could find. Mount shop details 27 B Paramount Dve Hendn 0-9-836 2304 440 Church St Pnrse 0-9-579 5965 I used the Nissan bushes for the radius arm bushes that connect to the axle. (pair) The winch challenge boys use t...

Hi Yah All Just ordered a EGT gauge and thermocouple from the states. While its comming I am seeking info on where you guys and gals out there have put the probes..(Be nice!) Photo's say a thousand words. I want to put it pre turbo for accuracy. I thought about utilising the blanking plate I used to...

Hi yah I have a KZJ78 also. I have just (been naughty) corrected mine by moving the hole on the forward attachment on the axle down by 14mm...(Cut off flange and welded new one on.) This has the effect of rotating the axle back into position. I used to run off set bushes, fine for onroad work but af...

Hi Yah DJ
Here is a link to a gear calculator where you can plug in your current settings and then in the other change one or more and see what you get.
Found it useful when changing gear ratio / tyre sizes.

http://www.grimmjeeper.com/gears.html

Cheers
Calvin

Took out the butterfly and remaining EGR system on the Prado 1KZTE. (Blanked off exhaust and intake a few years back) Had to do it insitu as I couldn't get the throttle body off. The intake manifold was still as clean as when I changed the head after it cracked...Years ago. Also set up the front end...

Thanks, will keep it in mind.
Will probably have to sell it on its own and look out for a 35 to buy.

Cheers
Calvin

Hi All.. Having upgraded from 33's to 35's I need to change the spare over. I have a NEW Hankook RT01 MT 33x12.5x15 . Been the spare and I am after a 35x12.5x15 in a Mud pattern. Anyone out there with a swap??? 35 must be WOF condition. With 50% tread on it...Pref. Contact Calvin 09 833 6262 021 147...

Hi John Nice to hear from you...The other forum went very quiet and I hadn't really been bothered lately. Been focusing on renovations on my house. Now that they are mostly complete I have had a chance to tweak the Prado. The old girl is going well...Just realised the other day we have had her 9 yea...

Hi All New member here, Calvin's the name...Been lurking in the shadows....Decided it was time to poke my nose out :D Been 4 wheeling for 8 years or so. Driving a 1991 Toyota Landcruiser Prado....The square one, coils all round. LWB. 1KZTE motor, winch, lift, retro fitted factory electric locker and...

Hi All Fellow club member had his Nissan stolen and I have posted details here if anyone can help. Please contact Peter directly Cheers Calvin Tyler His details are: Peter Meredith 021 207 2744 The truck is a Imported 1988 SWB 4.2 diesel manual but is badged a Patrol with custom stickers that I had ...