Search found 2863 matches
- Wed Apr 19, 2017 7:48 pm
- Forum: Nissan
- Topic: CODE 43 NISSAN TERRANO R50
- Replies: 11
- Views: 4294
Re: CODE 43 NISSAN TERRANO R50
the eti systems have more then one way of reading the position of the crank shaft, It can pick that up from the No1 injector lift sensor, and also from the timing advance on the injector pump itself, did your mechanic test the out put of the t.p.s through out the full travel of the pedal with a mult...
- Wed Apr 19, 2017 7:45 pm
- Forum: Nissan
- Topic: CODE 43 NISSAN TERRANO R50
- Replies: 11
- Views: 4294
Re: CODE 43 NISSAN TERRANO R50
If its the t.p.s it's the t.p.s, fly by wire throttle would put that atop the accelerator pedal assembly under the dash. i'd find it incredulous that the crank angle sensor would fail two years in a row as it is simply a magnetic pulse reader similar to that of a A.B.S system and they are subject to...
- Tue Apr 18, 2017 8:55 pm
- Forum: Nissan
- Topic: Crank sensor faults r50
- Replies: 1
- Views: 1213
Re: Crank sensor faults r50
three sensors at work there, which tells me you have a wiring issue, if it was a sensor you'd only get one code no1 lift sensor (which provides the TDC pulse signal) cam angle sensor ( its nowhere near the crank shaft) and the injection timing control valve (which is on the pump and why it has troub...
- Wed Apr 12, 2017 10:11 pm
- Forum: 4WD Parts
- Topic: Wtd EGR cooler core .
- Replies: 3
- Views: 969
Re: Wtd EGR cooler core .
2 inch connections? inch water lines, sounds like you need a water to air intercooler of a subaru
- Wed Apr 12, 2017 8:15 pm
- Forum: This weekends achievements
- Topic: 8th/9th april 2017
- Replies: 2
- Views: 3702
Re: 8th/9th april 2017
what a bog :( was the terrano on its side before the recovery, or during the recovery? Day one they put it on its side and further down the bank, next morning I wen in with paj1 and some more gear and hauled it up. Gave it half an hour to let the oil drain back to the sump, hooked the jumper leads ...
- Wed Apr 12, 2017 7:05 pm
- Forum: This weekends achievements
- Topic: 8th/9th april 2017
- Replies: 2
- Views: 3702
8th/9th april 2017
yep. It's wet out in the waikato. http://i1309.photobucket.com/albums/s621/crashbandicoot2/17862325_1693361594013777_2795128868280111305_n_zpshlsowq6b.jpg?t=1491893972 http://i1309.photobucket.com/albums/s621/crashbandicoot2/17630069_1674445039238766_6063590399457626240_n_zpsddowrdvw.jpg?t=149189397...
- Tue Apr 11, 2017 2:24 pm
- Forum: Projects / Mod's
- Topic: paj1 build up
- Replies: 70
- Views: 21419
Re: paj1 build up
F.Y.I.
There ate three depressions across the bonnet subframe. They are designed to fold the bonnet in half in the event of a head on collision so the bonnet doesn't get shoved through the windscreen. Make sure where you cut is either in front or behind these depressions or it will be a WOF fail
There ate three depressions across the bonnet subframe. They are designed to fold the bonnet in half in the event of a head on collision so the bonnet doesn't get shoved through the windscreen. Make sure where you cut is either in front or behind these depressions or it will be a WOF fail
- Tue Apr 11, 2017 2:21 pm
- Forum: Projects / Mod's
- Topic: paj1 build up
- Replies: 70
- Views: 21419
Re: paj1 build up
dvk-kp wrote:That's cool, obviously not to concerned about water dumping in over the engine? Well sealed dizzy really like how that looks, probly going to copy!
Can of aerosol tire shine mate. Waterproofs and stops the mud sticking come time to water blast.
This weeks top tip.
- Sun Apr 09, 2017 7:40 pm
- Forum: Toyota
- Topic: calling 1KZTE (spec. kzn185) gurus
- Replies: 22
- Views: 7392
Re: calling 1KZTE (spec. kzn185) gurus
watch your wallet and your expectations mate, the 1kzte is a 97kw engine you can throw thousand and thousands of dollars and hundreds of hours of research and labour at it and if your lucky make 30%-50% gains which = net 130kw to 150kw which is pretty low down on the scale of performance, you could...
- Sun Apr 09, 2017 7:30 pm
- Forum: Projects / Mod's
- Topic: paj1 build up
- Replies: 70
- Views: 21419
Re: paj1 build up
Looks good, are they to let the heat out of the engine bay? Yep. I converted the a/c radiator into a trans cooler which had a bit of a consequence on the actual radiators ability to transfer heat so tends to get a little bit warm. Bit the trade off is worth it as the trans temp rarely hits 100 degr...
- Sat Apr 08, 2017 9:22 pm
- Forum: Projects / Mod's
- Topic: paj1 build up
- Replies: 70
- Views: 21419
Re: paj1 build up
Been a while, few little things goin on. Cut some 'oles in the bonnet https://scontent-syd2-1.xx.fbcdn.net/v/t1.0-9/18951168_1460265210698717_8304767871552071836_n.jpg?oh=850ecafb47a4785799446eb963973d28&oe=5A065AD6 https://scontent-syd2-1.xx.fbcdn.net/v/t1.0-9/20032132_1460265160698722_62867486...
- Sat Apr 08, 2017 9:16 pm
- Forum: Tool Shed
- Topic: What is this thing? Welder/electric motor?
- Replies: 7
- Views: 3322
Re: What is this thing? Welder/electric motor?
says A.C motor on the right hand side and it has normal single phase 240 volt output aswel
- Fri Apr 07, 2017 8:41 am
- Forum: Toyota
- Topic: calling 1KZTE (spec. kzn185) gurus
- Replies: 22
- Views: 7392
Re: calling 1KZTE (spec. kzn185) gurus
Colder the better. When you start feeding extra fuel into it the egts will shoot up under load anyway . you want it running at normal temperature when it is working its hardest.
- Sun Mar 26, 2017 6:16 am
- Forum: Mitsubishi
- Topic: Pajero transfer box
- Replies: 2
- Views: 3099
Re: Pajero transfer box
Don't think so. My 3.0v6 is a auto is a m700 trans same as what's behind the 1uzfe and guys use the gearset from the manual deleca vans to get lower ratio in low range would deduce that the pre95 are interchangble but the 3.5 is a different trans etc my sisters one is a 3.5 so will attempt to find oit
- Wed Mar 22, 2017 7:31 pm
- Forum: Diesel Engines and Modifications
- Topic: Blow by and vapor leak
- Replies: 3
- Views: 3482
Re: Blow by and vapor leak
Pj_Marsh wrote:I'll price up some rings, cheers crash. Reckon I should do a compression test first?
Yep.
- Tue Mar 21, 2017 4:17 pm
- Forum: Diesel Engines and Modifications
- Topic: Blow by and vapor leak
- Replies: 3
- Views: 3482
Re: Blow by and vapor leak
Valve stem seals or worn rings. if cold once they warm up the tolerance closes up
- Thu Mar 09, 2017 11:44 am
- Forum: Nissan
- Topic: D21 Navara td27 n/a Power Issues!
- Replies: 5
- Views: 1823
Re: D21 Navara td27 n/a Power Issues!
Compression is down or injector timing needs dialing in closer to tdc
- Wed Mar 01, 2017 5:31 pm
- Forum: Nissan
- Topic: Mistral R20 Brake squeal
- Replies: 6
- Views: 1775
Re: Mistral R20 Brake squeal
Some brands of pads are hard compound and will take some time to bed in.
I prefer to use a softer compound pad and change them more frequently as it also saves the rotors
I prefer to use a softer compound pad and change them more frequently as it also saves the rotors
- Tue Feb 28, 2017 7:17 pm
- Forum: Nissan
- Topic: Mistral R20 Brake squeal
- Replies: 6
- Views: 1775
Re: Mistral R20 Brake squeal
check your wheel bearings?
skim the rotors, mistral rotors are undersized for the wieght they are expected to stop. So glaze quite easily ...or run a sanding disc on a grinder around them lightly...
skim the rotors, mistral rotors are undersized for the wieght they are expected to stop. So glaze quite easily ...or run a sanding disc on a grinder around them lightly...
- Tue Feb 28, 2017 11:08 am
- Forum: 4WD Parts
- Topic: FS QD32 Air Con Pump Set Up
- Replies: 2
- Views: 861
Re: FS QD32 Air Con Pump Set Up
MihiT wrote:I'll put my name on it. I suppose it's 12v though? And anyone from our courier service heading North?
I dont see why they wouldnt take 24 volt...its just an electromagnetic clutch
- Mon Feb 27, 2017 7:18 am
- Forum: Nissan
- Topic: TD42 no oil pressure!
- Replies: 11
- Views: 3484
Re: TD42 no oil pressure!
Via the threaded portion of the oil filter fittings. Jam a super cheap funnel or hose and funnel and pour some oil down it. Its possible that it could be dry and wont pull oil up from the sump .
- Sun Feb 26, 2017 9:21 pm
- Forum: Nissan
- Topic: TD42 no oil pressure!
- Replies: 11
- Views: 3484
Re: TD42 no oil pressure!
might sound odd, but what oil filters are you using?
- Sun Feb 26, 2017 9:11 pm
- Forum: Nissan
- Topic: TD42 no oil pressure!
- Replies: 11
- Views: 3484
Re: TD42 no oil pressure!
from memory there is a relief valve on the oil cooler too, but if the relief valve isnt bleeding oil when you crank i'd say the pump collar is broken.. the oil pump is driven off the crankshaft & cam drive gear in the front of the engine, its not uncommon/unheard of for them to not build pressur...
- Sat Feb 25, 2017 10:09 pm
- Forum: Toyota
- Topic: one off toyotas
- Replies: 12
- Views: 3114
Re: one off toyotas
it'll be riding on a ln106 chassi probably
- Sat Feb 25, 2017 10:08 pm
- Forum: Tool Shed
- Topic: Is there any mechanics in Hamilton
- Replies: 2
- Views: 1643
Re: Is there any mechanics in Hamilton
pm me details and ill see what i can do
- Sat Feb 18, 2017 7:44 am
- Forum: 4WD Parts
- Topic: WTB R20 - manual - diesel driveshaft and x member.
- Replies: 7
- Views: 1308
Re: WTB R20 - manual - diesel driveshaft and x member.
I'm wanting the following parts due to converting my WD21 Terrano to a QD32 engine and FS5R30A gearbox ( both from D22 ) Driveshaft from an R20 Diesel Manual. Cross member from an R20 Diesel Manual I'm in Wellington but I don't mind paying shipping. Interesting, when I did the swap to the R30A gear...
- Fri Feb 17, 2017 6:21 pm
- Forum: 4WD Parts
- Topic: WTB R20 - manual - diesel driveshaft and x member.
- Replies: 7
- Views: 1308
Re: WTB R20 - manual - diesel driveshaft and x member.
Few around with manual. One on tm recently
- Tue Feb 14, 2017 8:39 pm
- Forum: Toyota
- Topic: 1kz-te using water........
- Replies: 15
- Views: 8723
Re: 1kz-te using water........
It may be leaking to the crank case and being a minimal amount evaporation via the breather.
- Tue Feb 14, 2017 11:14 am
- Forum: Tool Shed
- Topic: WallysCustoms?
- Replies: 6
- Views: 2892
Re: WallysCustoms?
yep. no actual design rules as such for exo cages on cabed 4x4's/trucks, the LTNZ classes them as heavy duty ladder racks provided the barwork is within 100mm of the body
- Mon Feb 13, 2017 9:11 pm
- Forum: Nissan
- Topic: 1996 terrano TD27eti Valve clearance
- Replies: 5
- Views: 1287
Re: 1996 terrano TD27eti Valve clearance
Thanks, never thought to take pump sprocket cover off. One thing that surprised me is how easy the engine is to turn over. Fairly big bar on it though, but thought I would see where the notch was on the pulley for the compressions, but you can hardly feel them. Should I be concerned? Yes it does st...