Page 13 of 16
Re: v8 barbie make over.....
Posted: Mon Jun 23, 2014 10:41 am
by yeti
XJCrawler wrote:yeti wrote:So cause I'm really gentle doing shit I now have to pull locker so I can replace the inner seals I damaged putting axles in ....
Did you just do that on sat?
One before but hey who's counting ...
Re: v8 barbie make over.....
Posted: Sat Jun 28, 2014 9:37 am
by yeti
Re: v8 barbie make over.....
Posted: Mon Jul 07, 2014 7:53 pm
by yeti
great weekend at cust with the winch challenge....ironman class was a great success..think there was 25 trucks all up 12 being in the ironman class.......
got through 7 stages boiling again so parked her up think we may have a gasket problem or cracked head...
shit happens ......................................
Re: v8 barbie make over.....
Posted: Tue Jul 08, 2014 5:24 pm
by yeti
well fark it she's gonna have to go out the back now.......
Re: v8 barbie make over.....
Posted: Tue Jul 08, 2014 5:34 pm
by yeti
also found out temp gage doesn't work properly apparently......
Re: v8 barbie make over.....
Posted: Tue Jul 08, 2014 6:09 pm
by rokhound
Re: v8 barbie make over.....
Posted: Tue Jul 08, 2014 6:28 pm
by yeti
fark you .....
Re: v8 barbie make over.....
Posted: Tue Jul 08, 2014 7:22 pm
by Checkerhead
(please none of you point out that mine is also in the rear)
Re: v8 barbie make over.....
Posted: Tue Jul 08, 2014 8:09 pm
by Heath
Dont you worry about having something under pressure being shaken in the back that might suddenly spray hot liquid over your back?
Or is it just a jeep thing?
Re: v8 barbie make over.....
Posted: Tue Jul 08, 2014 8:26 pm
by yeti
Heath wrote:Dont you worry about having something under pressure being shaken in the back that might suddenly spray hot liquid over your back?
Or is it just a jeep thing?
you sick bustards..................
Re: v8 barbie make over.....
Posted: Tue Jul 08, 2014 8:27 pm
by yeti
Checkerhead wrote: (please none of you point out that mine is also in the rear)
Re: v8 barbie make over.....
Posted: Tue Jul 08, 2014 8:35 pm
by Heath
Re: v8 barbie make over.....
Posted: Fri Jul 25, 2014 1:39 pm
by XJCrawler
Found barbie's older cousin
Re: v8 barbie make over.....
Posted: Tue Jul 29, 2014 5:52 am
by kaney
yeti wrote:great weekend at cust with the winch challenge....ironman class was a great success..think there was 25 trucks all up 12 being in the ironman class.......
got through 7 stages boiling again so parked her up think we may have a gasket problem or cracked head...
shit happens ......................................
Its about now we mention lasting 29 seconds then wayne???
Great Day out, Good enough to convince me to get another toy dammit
(your co-driver for me next time though)
Re: v8 barbie make over.....
Posted: Tue Jul 29, 2014 6:38 pm
by yeti
kaney wrote:yeti wrote:great weekend at cust with the winch challenge....ironman class was a great success..think there was 25 trucks all up 12 being in the ironman class.......
got through 7 stages boiling again so parked her up think we may have a gasket problem or cracked head...
shit happens ......................................
Its about now we mention lasting 29 seconds then wayne???
Great Day out, Good enough to convince me to get another toy dammit
(your co-driver for me next time though)
um 26 bro ....
yep ill navi for ya cause I know what ya brought .....
ya got it yet
Re: v8 barbie make over.....
Posted: Wed Jul 30, 2014 7:40 pm
by kaney
Not yet. I need to find someone to go pick it up for me. I have no time at the moment
Re: v8 barbie make over.....
Posted: Mon Aug 11, 2014 8:52 pm
by TJ
Have you done anything to your tie rod and drag link? Mine got bent over the weekend and I'm doing research to find a stronger replacement than factory. But other than the Crown Automotive HD Kit for RHD, there doesn't seem to be much.
Currie/Savvy kits are for LHD only. Can't be flipped, the cross over joint will hit the passenger side sway bar link/bracket.
Re: v8 barbie make over.....
Posted: Tue Aug 12, 2014 2:53 pm
by yeti
bent mine a few times bout as thick as straw......waiting on James and see how his xj front end comes out ...doing some wj bits .....its all in his build thread ...xjcrawler ......just wish he would hurry up .....
Re: v8 barbie make over.....
Posted: Tue Aug 12, 2014 3:31 pm
by TJ
Well, in that case I might just go with Crown HD kit this time and see how it goes with James for next time I bend it.
May be I should just raid my wife's WG for parts plus V8 and get her something else to drive....
Re: v8 barbie make over.....
Posted: Sat Oct 25, 2014 11:15 am
by yeti
she shrank .......put old lift back in .....have got bits on order as in flares and bits ...........should be a road going heep in a couple of weeks .....
Re: v8 barbie make over.....
Posted: Mon Oct 27, 2014 7:36 pm
by callum007
what have you done with the coils you've removed? Im after a set about that size to trial/buy.
Re: v8 barbie make over.....
Posted: Wed Nov 05, 2014 4:50 pm
by yeti
[attachment=0]image.jpg[/attachment
Ok wof sheet is a long sheet ... But nothing major .. Go figure ...more new bits .. Old lift sitting on shelf will go back in at some stage .... Maybe
Re: v8 barbie make over.....
Posted: Sat Nov 29, 2014 7:43 am
by yeti
tie rod ends done ...new windscreen in muffler to do , headlights ,ball joints fun things them ...
looking rather small nexts to kaneys rig......still will be able to run 35s when done ......low and slow...
Re: v8 barbie make over.....
Posted: Mon Dec 08, 2014 5:54 pm
by yeti
seems legit ...............
Re: v8 barbie make over.....
Posted: Fri Feb 20, 2015 10:07 pm
by yeti
Re: v8 barbie make over.....
Posted: Sat Apr 25, 2015 11:06 am
by zukmeista
Re: v8 barbie make over.....
Posted: Sat Apr 25, 2015 12:35 pm
by Checkerhead
Heard he is getting a Landcruiser.
Re: v8 barbie make over.....
Posted: Sat Apr 25, 2015 4:29 pm
by yeti
going beach hopping.......wash ya mouth out Aron.....
Re: v8 barbie make over.....
Posted: Sun May 03, 2015 4:45 pm
by yeti
Re: v8 barbie make over.....
Posted: Sun May 03, 2015 8:21 pm
by churchill
Wow
Just wrap some insulation tape around, she'll be right...