X5 Project.

User avatar
1bad4x
Hard Yaka
Posts: 188
Joined: Thu Jun 28, 2007 12:00 pm
Location: Auckland
Contact:

X5 Project.

Postby 1bad4x » Sun Apr 16, 2017 3:06 pm

Well this should be fun.

No Haters please, yes they are a soft-roader... but how much we will see...

So I picked up my BMW X5 2001 got it cheap as it has water contamination in the Transmission, & Trans oil in the coolant..
Mmm nice messy job..

So jack & tools out & lets Get into it,

has taken about 40lt of trans oil to flush it out. started by removing the pan & filter, replaced filter & reinstalled clean pan, Removed cooler & put feed line in bucket & the return hooked up to bottle & pump of fresh oil, ended up with pan & filter off, huge bucket under the trans & flexi pipe to the pickup straight into fresh oil container, now seems quite clean, and gone for new air cooler,

As for the coolant, stripped the radiator out, will replaced with manual one so it doesn't have the extra outlet for the cooler. pulled all hoses, expansion tank etc & cleaned with hot water & persil. flushed the motor with hot water from hose, after it was quite clean fitted it back together & ran it on water & persil (tuff on grease but low suds & gentle enough for clothes) then short trips round the block with water flush in-between, until clean water is all that drains out, only then it it gets the antifreeze,

Only now up to real test drive to see if trans has survived, then we can get onto the fun stuff. watch this space..
---------------------------------------------------------------------
Image

User avatar
1bad4x
Hard Yaka
Posts: 188
Joined: Thu Jun 28, 2007 12:00 pm
Location: Auckland
Contact:

Re: X5 Project.

Postby 1bad4x » Sun Apr 16, 2017 4:09 pm

Photo 35 min after unloading from tow truck.

Image
Last edited by 1bad4x on Fri Apr 27, 2018 6:53 pm, edited 1 time in total.
---------------------------------------------------------------------
Image

basics
Hard Yaka
Posts: 1511
Joined: Fri May 11, 2007 12:00 pm
Location: Wellington
Contact:

Re: X5 Project.

Postby basics » Sun Apr 16, 2017 4:30 pm

should be interesting
99 pajero exceed 3.2

User avatar
mudsurfv6
Hard Yaka
Posts: 640
Joined: Fri May 23, 2014 6:29 pm
Location: pahiatua

Re: X5 Project.

Postby mudsurfv6 » Sun Apr 16, 2017 6:23 pm

1bad4x wrote:they are a soft-roader... but how much we will see...


1bad4x wrote: then we can get onto the fun stuff. watch this space..


so whats the plan? simexs, lift, winch, exo........... :D
1996 vzn185 surf, TRD supercharger, SAS, 35s, 4" lift, 2 lockers, ute chopped + more happening. Andrew 0272226292.

User avatar
1bad4x
Hard Yaka
Posts: 188
Joined: Thu Jun 28, 2007 12:00 pm
Location: Auckland
Contact:

Re: X5 Project.

Postby 1bad4x » Sun Apr 16, 2017 6:35 pm

Already have winch, ruvna 9500 with competition gears.
Main list....
winch/bull bar
lift
33x12.5 on 20's
---------------------------------------------------------------------
Image

User avatar
fh2014
Hard Yaka
Posts: 304
Joined: Mon Oct 20, 2014 4:48 pm
Location: North Shore AKL

Re: X5 Project.

Postby fh2014 » Mon Apr 17, 2017 7:54 am

this is different, would be a real challenge. should be fun :D

User avatar
Crawlerer79
Hard Yaka
Posts: 305
Joined: Sun Jun 12, 2016 3:38 pm
Contact:

Re: X5 Project.

Postby Crawlerer79 » Mon Apr 17, 2017 9:33 am

Now this sounds interesting....
'The Big Truck' - 2001 TD5 Disco II
'Lando' - 1994 V8 Disco
'The Caramel Trophy Truck" - 1990 Disco Ex-Camel Trophy (?)

User avatar
1bad4x
Hard Yaka
Posts: 188
Joined: Thu Jun 28, 2007 12:00 pm
Location: Auckland
Contact:

Re: X5 Project.

Postby 1bad4x » Wed Apr 19, 2017 6:39 pm

Minor Update,
Trans Oil cooler installed, Test drive round the block, all seem's good.....
Tomorrow will get out for a good drive... fingers crossed.

Image
Last edited by 1bad4x on Fri Apr 27, 2018 6:53 pm, edited 1 time in total.
---------------------------------------------------------------------
Image

User avatar
1bad4x
Hard Yaka
Posts: 188
Joined: Thu Jun 28, 2007 12:00 pm
Location: Auckland
Contact:

Re: X5 Project.

Postby 1bad4x » Fri Apr 28, 2017 9:51 pm

Slow progress, Been for a few good drives & Trans seems to be Ok. phew, I Still don't full trust it But it's looking promising!

Some Pic's from before I got my Hands on it. Had to use the sellers pictures as the first photo I took was in pieces...

Image

Image
Last edited by 1bad4x on Fri Apr 27, 2018 6:54 pm, edited 1 time in total.
---------------------------------------------------------------------
Image

User avatar
1bad4x
Hard Yaka
Posts: 188
Joined: Thu Jun 28, 2007 12:00 pm
Location: Auckland
Contact:

Re: X5 Project.

Postby 1bad4x » Fri Apr 28, 2017 9:52 pm

Fun times ahead,

Some toys have arrived..

Image
Last edited by 1bad4x on Fri Apr 27, 2018 6:55 pm, edited 1 time in total.
---------------------------------------------------------------------
Image

BlakeNZ
Hard Yaka
Posts: 710
Joined: Sun Jun 16, 2013 10:50 am
Location: manawatu

Re: X5 Project.

Postby BlakeNZ » Sat Apr 29, 2017 8:16 pm

what motor do you have, the petrol 3 litre 6 cyl,or 4.4 or 4.8 V8? or the diesel?

User avatar
1bad4x
Hard Yaka
Posts: 188
Joined: Thu Jun 28, 2007 12:00 pm
Location: Auckland
Contact:

Re: X5 Project.

Postby 1bad4x » Sat Apr 29, 2017 10:06 pm

4.4 V8 would have liked the 4.8 but the 4.4 is still a V8 & parts are more abundant.
---------------------------------------------------------------------
Image

User avatar
1bad4x
Hard Yaka
Posts: 188
Joined: Thu Jun 28, 2007 12:00 pm
Location: Auckland
Contact:

Re: X5 Project.

Postby 1bad4x » Sat Apr 29, 2017 10:24 pm

A small peek at some progress today.

Image
Last edited by 1bad4x on Tue May 01, 2018 10:44 pm, edited 2 times in total.
---------------------------------------------------------------------
Image

User avatar
1bad4x
Hard Yaka
Posts: 188
Joined: Thu Jun 28, 2007 12:00 pm
Location: Auckland
Contact:

Re: X5 Project.

Postby 1bad4x » Mon May 15, 2017 12:04 pm

Well that was a little depressing...
After the trans behaving soo well for as long as it did I had got my hopes up.. Then reverse had other ideas,
Water & k's have killed it.
New one has arrived so mission for this week is to install...
Finished my 1st ever full wrap. imho she is looking the part.
Wheels & tyres on, minimal rubbing, need spacers as there is no poke at all. got 25mm rear & 20mm fronts. still waiting on the rears to come from Germany. had a little trimming to the front inner guard may need more when the spacers go on..
Dropped the template for the lift kit the engineer should be ready by the end of this week, found I can trick the rear airbags to allow me to set the height I want, and just about to the mm.

So the build is progressing well.

Image

Image
Last edited by 1bad4x on Tue May 01, 2018 10:44 pm, edited 2 times in total.
---------------------------------------------------------------------
Image

User avatar
fh2014
Hard Yaka
Posts: 304
Joined: Mon Oct 20, 2014 4:48 pm
Location: North Shore AKL

Re: X5 Project.

Postby fh2014 » Mon May 15, 2017 6:30 pm

did you have a trans temp gauge on it ?

User avatar
NJV6
Hard Yaka
Posts: 2749
Joined: Mon Nov 15, 2004 12:00 pm
Location: Southland
Contact:

Re: X5 Project.

Postby NJV6 » Mon May 15, 2017 6:53 pm

:D
Attachments
IMG_2352.JPG
SWB V6 Paj with one or two mods ;)

User avatar
1bad4x
Hard Yaka
Posts: 188
Joined: Thu Jun 28, 2007 12:00 pm
Location: Auckland
Contact:

Re: X5 Project.

Postby 1bad4x » Mon May 15, 2017 7:12 pm

Na,
Did the feel test on the pipes to the cooler, although quite warm, could hold them. so wasn't roasting.
have & am thinking about it just to know,
---------------------------------------------------------------------
Image

User avatar
1bad4x
Hard Yaka
Posts: 188
Joined: Thu Jun 28, 2007 12:00 pm
Location: Auckland
Contact:

Re: X5 Project.

Postby 1bad4x » Tue Jun 20, 2017 5:17 pm

Well has been a while since last update.

So before I got to installing new trans, she developed a timing chain rattle....

So over the last few weeks I have
Been sic with cold, Had a infected tooth pulled.
but on the car...
Pulled the front & done the timing chain guides, (learning on the fly)
Pulled the trans & installed new (again learning on the fly)
Test drive today...

Still waiting on lift kit (engineer lost sheet with details)

Wheels & tyres fitted, still have minor rub lift may fix that.
Full wrap fist time I have done a full wrap.
just ordered a BlueDriver scanner as that gives on the fly info, so should be able to monitor all sorts & no need for gauges.

Image


Image
Last edited by 1bad4x on Tue May 01, 2018 10:45 pm, edited 2 times in total.
---------------------------------------------------------------------
Image

User avatar
Clint
Hard Yaka
Posts: 632
Joined: Tue Feb 17, 2004 12:00 pm
Location: Rotoiti (North Is)

Re: X5 Project.

Postby Clint » Wed Jun 21, 2017 11:11 am

Wow, wouldn't have picked you'd fit a set of 33's on one of those without some very major mods! Will be interesting to see how it goes. It'll certainly look badass :twisted:

Cheers
Clint
UZJ71 Landcruiser
Jeep J20 - 1UZ-FE powered (part owner)
KTM 640

If it breaks, build it stronger.
If it doesn't break, drive it harder.

User avatar
1bad4x
Hard Yaka
Posts: 188
Joined: Thu Jun 28, 2007 12:00 pm
Location: Auckland
Contact:

Re: X5 Project.

Postby 1bad4x » Tue Jun 27, 2017 3:12 pm

So today she has had some surgery on her rear end, Gone from a J lo ass to a Gal Gadot
Departure angle has gone from a very unimpressive 28 degrees to a better 43 degrees & this is before the lift kit...


Image

Image
Last edited by 1bad4x on Fri Apr 27, 2018 6:57 pm, edited 1 time in total.
---------------------------------------------------------------------
Image

User avatar
mudsurfv6
Hard Yaka
Posts: 640
Joined: Fri May 23, 2014 6:29 pm
Location: pahiatua

Re: X5 Project.

Postby mudsurfv6 » Tue Jun 27, 2017 3:20 pm

Nothing wrong with just lo's ass, on her. :D :roll:

Looking good, gonna be interesting where this ends up.
1996 vzn185 surf, TRD supercharger, SAS, 35s, 4" lift, 2 lockers, ute chopped + more happening. Andrew 0272226292.

User avatar
1bad4x
Hard Yaka
Posts: 188
Joined: Thu Jun 28, 2007 12:00 pm
Location: Auckland
Contact:

Re: X5 Project.

Postby 1bad4x » Tue Jun 27, 2017 3:27 pm

mudsurfv6 wrote:Nothing wrong with just lo's ass, on her.


Maybe, just not on the back of a offroader.
I prefer Gal's but this could take the topic in a different direction.... :lol:
---------------------------------------------------------------------
Image

BlakeNZ
Hard Yaka
Posts: 710
Joined: Sun Jun 16, 2013 10:50 am
Location: manawatu

Re: X5 Project.

Postby BlakeNZ » Tue Jun 27, 2017 5:52 pm

i guess you will lose some of that 43 Degrees when you put a tow hitch socket on?
Did you know who Gal Gadot was prior to the wonderwoman role? She has acted in quite a few things, but i never took notice till the wonderwoman role.

User avatar
1bad4x
Hard Yaka
Posts: 188
Joined: Thu Jun 28, 2007 12:00 pm
Location: Auckland
Contact:

Re: X5 Project.

Postby 1bad4x » Tue Jun 27, 2017 6:25 pm

BlakeNZ wrote:i guess you will lose some of that 43 Degrees when you put a tow hitch socket on?
Did you know who Gal Gadot was prior to the wonderwoman role? She has acted in quite a few things, but i never took notice till the wonderwoman role.


Took me about 5 min in to Wonder Woman to work out Han's girl from Fast N Furious

wont loose any, got new detachable tow bar, & going to mod it so the bottom of the receiver will be same height as the bottom of the bumper. it has 12 bolts to attach it to the truck will swap most out for high tensile. it also attaches to the chassis rails. will also beef it up & get Recovery Hitch with 5ton Bow Shackle.
---------------------------------------------------------------------
Image

BlakeNZ
Hard Yaka
Posts: 710
Joined: Sun Jun 16, 2013 10:50 am
Location: manawatu

Re: X5 Project.

Postby BlakeNZ » Tue Jun 27, 2017 10:20 pm

"chassis"? (insert raised eyebrow here) :) I know what you mean.
What does your X5 have in terms of traction devices (eg lsd in rear, open diffs but with traction control etc)?

User avatar
geckoadventure
Hard Yaka
Posts: 550
Joined: Sun Nov 29, 2009 12:30 pm
Location: Malaysia
Contact:

Re: X5 Project.

Postby geckoadventure » Wed Jun 28, 2017 12:43 am

Wow going to be watching this build.

User avatar
1bad4x
Hard Yaka
Posts: 188
Joined: Thu Jun 28, 2007 12:00 pm
Location: Auckland
Contact:

Re: X5 Project.

Postby 1bad4x » Wed Jun 28, 2017 9:07 pm

BlakeNZ wrote:"chassis"? (insert raised eyebrow here) :) I know what you mean.
What does your X5 have in terms of traction devices (eg lsd in rear, open diffs but with traction control etc)?


Open diffs, Hill decent button & electric traction... this model was built when BMW was in bed with Range Rover so it had the benefit of Rover's off road experience.

If I end up going nuts.... It's been known to happen,
1st I would swap the transfer box with a RR to get the low range & I think centre lock. (Would need to research 1st)
not sure if there is a LSD avail so may go a N.Z.I.G. lokker (Unlikely though)
My other thoughts, get a 400+hp 760i donor & turn in to a 2wd race truck.
For now will just enjoy as is, even if it is bad enough to make driving shiny runs a challenge.
---------------------------------------------------------------------
Image

User avatar
1bad4x
Hard Yaka
Posts: 188
Joined: Thu Jun 28, 2007 12:00 pm
Location: Auckland
Contact:

Re: X5 Project.

Postby 1bad4x » Sat Jul 08, 2017 2:01 pm

Weekend update.

Lifted, had to go a bit less that hoped as the cv's would bind a little when wheel lifted.. so was abot 40mm front & 45mm rear.

Got trans temp gauge fitted & she's running nice & cool, even in stationary traffic.

Got the tow-bar modified & Recovery Hitch fitted.
Ended up with 8x m8 & 4x m10 high tensile & 6 factory bolts holding it all in place, so should be quite strong...

Just got to get the Exhaust finished & thats the rear sorted.

Ordered winch bar only to find its on 4 week back order :( gutted..

Image
Last edited by 1bad4x on Mon Apr 30, 2018 2:11 pm, edited 1 time in total.
---------------------------------------------------------------------
Image

BlakeNZ
Hard Yaka
Posts: 710
Joined: Sun Jun 16, 2013 10:50 am
Location: manawatu

Re: X5 Project.

Postby BlakeNZ » Sun Jul 09, 2017 5:06 pm

wow! didn't think anyone would make a winch bar for a X5. you will lose some of your 40mm front lift

User avatar
1bad4x
Hard Yaka
Posts: 188
Joined: Thu Jun 28, 2007 12:00 pm
Location: Auckland
Contact:

Re: X5 Project.

Postby 1bad4x » Sun Jul 09, 2017 5:38 pm

BlakeNZ wrote:wow! didn't think anyone would make a winch bar for a X5. you will lose some of your 40mm front lift


Your right no one does, Going Xrox for a ford ranger, will need some mods to fit & work. sim shape & width so hopefully it's just the mounting that needs work.
lucky that being a 2001 I don't need to have AirBag proven bar,

& yea will loose a bit, was governed by the working angle of the CV's height is one thing but binding CV's when wheel/s lifted is a very bad bad thing.. hopefully wont loose to much..
---------------------------------------------------------------------
Image

Return to “Projects / Mod's”

Who is online

Users browsing this forum: No registered users and 15 guests