Yup still got it. been using the winch to pull out fence posts and waratahs over the last week Swing past and we can unbolt and make to cardboard templates.... chucked the originals out.

W

done finally now Iv gotta design a rear one, has anyone got pics of a nice looking useable rear end.......... or this.. dropped the centre to allow for slightly larger tyre on std mount. https://lh5.googleusercontent.com/-M33C23_93Rc/Uo2p9UNuJxI/AAAAAAAANqk/aKIp7y2Y1Mk/s640/IMG_4831.JPG

chrome wrote:done finally now Iv gotta design a rear one,
has anyone got pics of a nice looking useable rear end..........

This one ok?

Hi, I have leaf and coil springs which I am sure are off a 70 Series ute. I will need to check the condition of the shocks but they will be thrown in anyway.

Pickup preferred as they are bloody heavy. Make a decent offer and head on over.

W

Looking nice there

how thick would a concrete pad need to be to mount this? probably nothing too outside of the norm neing a 4 poster I expect huh? wonder how it'd fare living outside...... I have seen two post install doc say 200mm for the larger 5T and 6T, as for the 4 post as the load is spread I would say this ...

4x4 wrote:How much you looking for?

I would recommend something local as freight would kill it even if it was free

No set price, make a decent offer and come pickup.

W

a bump for skid

W

For Skid... the ramps can swap ends so the motor/control could be at either end depending on your setup.

W

pruggerdore wrote:3 phase? or single?

3 phase motor but could easily swap for a single phase motor I assume.

W

on the post



The jack closest belongs to another hoist - the far end is air operated and comes with the hoist.

W

skid wrote:Pics biaaaaarch

Do you not know what a hoist looks like skid? I thought you guys in the tyre trade got rid of jacks lol. I will sort some out soon

W

Hi guys, anyone interested in a 4 post hoist? Pickup Carterton - in daily use and has one air jack which slides the length of the hoist.

Easy access, reverse a truck in and under the hoist and disconnect and drive away lol

cheers

W

Hi guys, I have a set of 4 new MT764 31" going for $1000. Drop me a message if interested. pickup prefered - Carterton

W

I should get onto this again otherwise I will just keep driving the little beastie

W

imsohi wrote:Geussing you are meaning the 762 bighorns???

Thanks corrected it

W

Hi guys/gals. I have stock sitting which is a cancelled order from a bugger of a customer. 4 of 35x12.5R15 MT762 Bighorn - $1550 for the set - pickup only 4 of 33x12.5R15 MT754 Buckshot - $1300 for the set - pickup only I may also have a set of 35" Silverstone MT117 too. W **edited to correct my ...

Thanks Derk.

derk wrote:be easier and smarter to biff the old transfercase and throw a split transfercase on it much stronger and easier to find bits for

'
'It would be if the client did not want to keep as much as poss standard

W

Hi Derk, seals, bearings are all easy to sort out the gear and shaft less so.

W

Hi guys, we have a customer with a totally mint FJ40 ('77) and we are rebuilding a lot of the running gear. Looking for an in great condition idler gear and shaft from the transfer case - current one's hardening has worn off and gear has a bunch of corrosion from bad storage. May also be looking at ...

pm sent

I think we have scared her off with all the offers flying thick and fast

W

pm sent

Just getting ready for my winch setup. Have a second battery tray and a battery. Not sure whether to go with a controller or just have them connected full time with an isolation switch just in case. Thoughts? Also where in the kapiti/wellington area is a good place to get some cables made up ...

Anyone out there want to give me a price to convert my 1985 Prado to v8 or v6 Must be a high quality job. Take a read over http://www.offroadexpress.kiwi/Forums/viewtopic.php?f=38&t=40035 This should give you a good starting guide. There will be variances on the condition of your truck, timeframes ...

catalystracing wrote:Thanks for the time and effort you put into this...

Absolutely - shit like this takes AGES and can be a total pain in the ass. WELL DONE Mike!!!!

W

Hi guys, on behalf I have a 4x4 91 Delica sitting which may be getting put up for sale. It had been used for a work wagon so ply on the floor but also has all the seats available (currently fitted). Be good for a 4x4 work wagon or a 4x4 tourer I would think. They are looking for around $4k but ...

tomsoffroad wrote:Ive just ordered a teng tools roll cab cant comment on quality cos I aint seen it yet cant wait as im sick of hunting for spanners

I use Teng tools and cab - I like them both. Good metal drawers, positive lock when closed, smooth and good sized handles.

W

hamishh wrote:How much you after William I got a mate who is after one of these little beasts

Not sure at this stage Hamish, mate is more than welcome to look it over and make an offer.

W