Hey Dan, whats Darinz damage like is he twisting the spline or damaging the spline shoulders.... the dezert boys are very concerned about DS plung movement and will build to eliminate it because even a little bit can cause failure (shoulder profile damage), as the suspension movement at speed will ...

Your uppers look to short, they wanna be around 80% of the length of the lowers. Should help with your pinion angle change. but mess with everything else

Darinz only has a few ( like 3 degrees) total change, and only about 5 mm length change and it is eating driveshafts. The spline is the problem so not sure if an alignment thing. One thing to consider though is you rarely run at ride height, even on flat ground you will squat under acceleration ...

Looks like it's all sold sorry. (As of last night)

How short? I had a lux transfer on the back of a nissan RWD Auto and that was shorter than a zuk box and divorced case. You will find most RWD autos have quiet a long tail section that can be cut off. doing that took about 230mm out of the nissan auto. It always amazes me how much shaft there is in ...

Bump

I am over this taking up space in my shed. Make me an offer, what that offer is will decide how many of the "extra" bits (seats, steering, etcetc) that go with it.

Tiny bit of virtual progress to show the tangent that my build is potentially taking. http://i269.photobucket.com/albums/jj73/shortylux/lowerlink_pic_zpsklf1mlmj.png Talk to Darinz about his, they have been well tested and through cert. You should talk to him about the bomb proof front arms, they ...

Body is now sitting on LWB chassis, with exo sitting over top. Exo needs further work as it was originally over a shorter body. Body is about 90% done. All glass and rubbers are there. Fibre glass bonnet As it sits I'm after $1500, if I get motivated and spend any time on it price will go up ...

Don't use the body. Earth the ecu and all the sensors etc on the engine, usually the manifold. Factory there will be a couple of earth points on the head side of the inlet manifold fairly easy to get to. The ecu reads tiny differences in voltage from the sensors ( remembering most are only max 5v ...

Motor, trans and associated bits sold Crappy photo of body attached. Have all the glass and rubbers to fit. image.jpg Edit , no idea why it is upside down nor any idea how to right it sorry Still got hilux transfer ( forward shift) and the steering box, shafts, quickener along with chassis's and ...

Will get some pics at the weekend. Most of it is stored away or buried under other junk.

Anything in particular you want to see? Oh and delivery assistance prob won't stretch to the other end of the country

Right so after stripping my winch challenge Zuk with plans to rebuild it with a bit more wheel base and a closed in cab my plans have now changed. So for sale is everything but the winch (I'm keeping that) and axles ( there gone) Swb chassis modified mounts and front end slider attached Lwb chassis ...

Located whangarei.

Sold pending

Bit of both, have plans for newer version of what I had, bit more of a off road racing focus. Although at the moment family and things are coming first so could be another couple years before I'm done Might run another event while I have nothing to drive at some point too

Hilux 4.88s for sale. One on LSD centre the other on ARB locker. ARB will have solenoid and switch no compressor and is currently in complete front housing with custom mounts. LSD is in rear housing with disk brake conversion and custom mounts Will not be any cheaper without the housings as I would ...

See Mike at Runva Winches. There motors bolt up. I ran a couple on my 8274 ( twin motored) and they handled all the abuse I could throw at it. You know which challenge stuff like full stall at low volts after a big winch with dying alternator, usual sort of motor killing stuff. Still look good as ...

I've got one up here in Northland, arrange transport and it's yours. I can't really be arsed packaging it for the rough as freight companies so ORE courier might be best option

Sold

Going on trademe shortly. Feel free to PM me an offer, I won't be offended but I won't give it away either

Someone must want/need one. My son has his eye on a new gocart and mum says toys for toys so this is the least used toy i can find to part with

Pics attached. Second motor looks like the one attached. Enough wiring to connect and make go also included. If you want wire rope it is on a different drum I will swap in (only 1 drum for sale)

Winch has breather and oil drain fitted too.

Don't ask why pics are upside down cause don't know

Post up a pic of the warn motor with the broken end cap. I have a couple different older warn motors here that are stuffed but have good caps. If I have a matching one I'll flick it down to you and you'll have a mint motor to sell http://images.trademe.co.nz/photoserver/tq/332675966.jpg If you have ...

I have a complete Warn 8274 for sale. 12v with soliniods controller etc. can also come with wire rope if wanted.

Can get it to Tauranga first weekend of October or I am sure the ORE courier service will be able to help get it further south.

$950ono (for right price it will may come with spare motor)

Post up a pic of the warn motor with the broken end cap. I have a couple different older warn motors here that are stuffed but have good caps. If I have a matching one I'll flick it down to you and you'll have a mint motor to sell

Appears to be essentially unmarked, drove onto tow truck Lots of other stolen gear at same address. 2 offenders charged and remanded to Monday at this stage

Located this afternoon in rural Kamo

I have done this in my winch truck and have a couple mates who have done it on road trucks. 3 relays and 3 diodes are required. The shifter can then be used to control L 2 D and the OD switch OD. The shifter has power outs for each shift location to tell the TCU what you want to do, it decides if ...

Trade me fella is right its pretty easy to make it run. There are only about 5 wires to the ecu and the starter wiring to deal with if you dont want to mess with all the nice to have stuff like idle ups etc. The auto runs its own computer and there are a few shared signals and to / from signals ...

I've done a CA18 which is pretty similar. There is heaps you can cull out not only AC stuff but idle ups, cold start etcetera. Key is get a full factory manual for the car ( bonus of SR stuff is boy racers love them so search SR20 fsm and you'll find one). They have individual wiring diagrams for ...

Linkage BUT Teranos are cable and the shifter is the same pattern and throw so work. Have actual experience with this.