yup mines an 88" can be seen here http://www.offroadexpress.co.nz/Forums/viewtopic.php?f=18&t=10608

Damn right when ive got no cash I wont be able to do anything for about 3 weeks at the mo, so once im sorted ill post back here, hopefully its still available then but if not thats ok

must be a ore discount @ 100, seen the tardme auction lastnight that u got it listed for 200

Id be keen on this round xmas, if u still have by then that is. abit short on funds atm but wanting to put a second tank in my landy n its diesel so that'll work out good

Dave

Hi All, Im after a set of leaf springs for my 2A, both front & rear, 2nd hand decent condition ones would be good, oh & cheap if possible. Basically need a good set that will pass compliance for re-registering at this point, once i have the cash ill look at getting new ones, Not worried where in the ...

Hi All, Im after a set of leaf springs for my 2A, both front & rear, 2nd hand decent condition ones would be good, oh & cheap if possible. Basically need a good set that will pass compliance for re-registering at this point, once i have the cash ill look at getting new ones, Not worried where in the ...

Hey Mike,

saw this earlier today, its not a 3.9 but its cheap, lol.

http://www.trademe.co.nz/Trade-Me-Motor ... 642599.htm

also thought i'd add in, the conversion that im lookin at doing is to use parts that are the most popular to get ahold of i.e. disco parts so that way replacement parts are easy to get, im also going to suss out the disc handbrake conversion, now i know most ppl want a easy swap to be done n thats ...

Flyingpony wrote:Link to another Series with DIY disk brake conversion:
http://forums.lr4x4.com/index.php?showtopic=22910

that info from that site is the info i posted up at the start of this thread but i didnt get it from that site i got it from a different site, just thought i'd say, it seems that this conversions gotten around abit

Heya Terry,

thanks for the offer but ill have to pass on it because i dont have access to 3 phase, thats the main reason i'm after one thats single phase, offer it up on here u might get some taker's.

Cheers
Dave

if i get time off from the boss ill make it there but only to watch the landy's outa action so no driving for me but keen to head out

ok I found the pic's that I took so I thought I better upload them http://i282.photobucket.com/albums/kk277/djnlandy/My%20Landy%20Pics/Pic1.jpg http://i282.photobucket.com/albums/kk277/djnlandy/My%20Landy%20Pics/Pic2.jpg http://i282.photobucket.com/albums/kk277/djnlandy/My%20Landy%20Pics/Pic3.jpg ...

Heya Guy's, I've been thinking & its time i sorted out my tools, seen as all i have is a very basic set now, i did have all the tool's i needed but wrong decision's made me end up with no tools ok I'm after a mig welder around the 180amp mark, i dont really want to go any lower in amp's, i would go ...

yup i'm gona make it my new mission to get this conversion done

4 point disc brakes plus a disc hand-brake

pm sent aswell

Dave

Do you a whole sIII if you want, 109" $100 ex yard Taranaki. i'm tempted very much to say yes but i better not im really strapped for cash at the mo, if i can get away with just getting the driving members for the diff i have then atm thats the best thing for me, n yup i should of actually looked ...

ok found it

http://www.x-eng.co.uk/X-BrakeSeries.asp

thats the disc hand-brake, i've emailed the agent in ozzie to see how much the kit is going to cost with freight included.
i'll also email the ppl of the disc brake kit from the first post of this thread n see how much they charge for that unit, ill post up the info as soon as i get it

i've also found the pic's i saved of the disc hand-brake i saw on the net while surfing, im just trying to find the info that went with the pic's, i thought it'd be a good idea to try n make up a kit that included all 4 hub's being able to be changed over to disc & also the hand-brake at the same ...

Is this a topic on makeing your own conversion, or are you open to other members Disc Bake conversions and how they made them, as I don't want to do a thread jack. Have they been low volume certed? i made this thread up to see if someone was able to make up a plate here in nz that way i didnt have ...

i have to pull the parts landy apart so im going to make up a mock unit n get the measurements n stuff done up, but give me till next friday for any sort of confirmation on the measurments

yea my thoughts are the same as to the amount of grinding that he did, he does also say that he did go abit over board on the grinding n that not as much was needed in the final setup but he doesnt post any pic's a similar plate as to the one used in that set from that link could be made up to solve ...

just had a thought. Possible pack ? 4 Plates 2 Oil Retainer Rings 4 Spacers now as to doin the plates for the rear, i'm thinking a plate could be made up but made similar to the original mock up ( plywood version ), also would have to see if the oil retaing rings would be needed for the back ( im ...

Here's a short view of the parts used: Calipers: off a 98 300tdi 90 Disc's: Landover 110 2001> (non Salisbury axle) Part number is SDB000330 I've got disco and rangie calipers here. I should measure and draw them up in solidworks one of these days. There are also a range of defender calipers which ...

pm jafa with you details he has a cnc mill you coudl make it on a centerlathe and a dividing head probaly take 2 houra a side to make were as on a cnc i woudl expect a 20 min maching time + progamming for the first set and a tooling/setup per run cost This is the Draw up the guy had for the Final ...

Now Just one thing to remember this was all done & the guy fitted 15inch rims!!!! Just so everyone reading knows, this following write up is not from the link i posted in the first post, i cant remember where i found this following write up So here is a little contribution to all series owners who ...

yea that's wat i was thinking about too. the other write up i have saved is of a similar set up, the plate is aslo just about the same design as the one used on that kit, but the calipers used on the write up i have were from off a later model discovery, alot of calipers for those models can be ...

Heya Guy's, now i know theres been a few diff methods to how ppl have applied disc brakes to a series landy,i've seen about 5 diff ways myself n i came across this site that has a kit made up, i only just came across it but thought i'd post it here n if anyones interested. i've got another write up ...

Hi Guys,

ok i had to edit this thread

I'm looking for a LWB roof, with side's & also a LWB chassis

im going to be using it on a project i'm thinking of

Anyone know of one going can u drop me a line plz.

Cheers
Dave

i've only just started lookin for a unit to use

i'll keep that in mind about the MQ power steering unit

after these small parts are paid for next on the list is going to have to be a mig welder

ok i just re-read ya reply n yup the lights on this time if the standard drive members for the hubs arent 24 spline'd then yup i will have to get the ones that u have, coz i wont have any here even thou i got 2 std rover diff's Let me know how much u'r looking for & include postage to whangarei n ...

Heya Guys, I'm looking at putting in a power steering unit in the landy & I was wondering which box would be the best one to use, ( i.e. the one that needs the least amount of mod's done to fit it) I was thinking has anyone put a falcon power steering box in ?? i know it'd be a good unit to use ...

bummer about auction goin up that much, i hate it when it does that too, atleast u'r able to get 2 units,

hopefully u'll be able to make one good one out of the 3 now n u'll have enuff spare parts