My gearbox went today on my old hilux. Anyone got a good one kicking around.

Closer to Queenstown the better.

Still for sale.

Mileage is 250000km Its Diesel (12ht engine) I had to sort out a front break imbalance and a leaky hub seal for the WOF. So rebuilt the calipers, new pads and hub seal. Sorted. Don't think there was anything about down for next WOF. It's started runs a little cool if anything, may need a new ...

Coppermine Creek on the west coast. Great trip

No one interested before i stick it on TM?

old video of the truck.

http://www.youtube.com/watch?v=3o7rXIvZTNE

so im selling my 60 series cruiser. 1987, 4Lt turbo. Runs great. The good bits, Spring over lift. snorkel. PTO winch. LSD in the rear. 10x15 rims. 35" maxxis bighorn. hocks back and front. custom inter cooler. Oversize exhaust. Roof rack. very little rust for year. few spear parts included. All ...

rear leaf springs wanted for my 87 60 series cruiser anyone got a some or know where i might pick some up cheap?

Otago area or willing to post.

right just has a look and it said on the plate 690mm F 700 R and from the center of the front hub to the bottom of the arch is 700mm. think im going to sort the other small bits and argue the toss.

) The suspension height is however listed - measured from the centre of the hub to the bottom edge of the guard. Tyre height is included in that and an allowance of a difference of +/- 5% that's odd as i fitted got aftermarket arch flares a year ago and there lower then standard ones. may be i ...

has it always had 35"s or have you gone up in size recently? it had 37s on for a bit and passed at VTNZ. the next time they failed it with 35s so took it some where else and passed so took it to them this time and fail on 35s. thinking i may borrow a set of standard wheels from a friend and put ...

so my 60 series failed the WOF today because its 50mm over the cert plat height. it has a spring over. also failed on the 35" tiers as they aren't mentioned just the 10x15 wheels. the last WOF i took it to at the same place said the spring were flat and it had to be raise so i got the front spring ...

got to be worth $400 but make me an offer!

still here

complete front axle/diff, standard ratio. was told it has new CVs and the hubs were rebuilt not so long ago. include disks and locking hubs. not lsd or locking.

open to offers.
pickup Queenstown.

this one. but without the rope.

pto winch and bumper from my old 60 series. very strong winch, worked well but have two and need to clean out the shed.

open to offers.

pickup queenstown.

put some photos up from the weekend on my site if you fancy a look.

http://lukesergent.co.nz/blog/

still got it. also just put it on TM so be quick if you wont it.

The force is strong with you luke.. gimme a tinkle regarding when ya getting it.. I think couple of us can help..spoke to Bert.. so got a idea of what ya done.. no worries, i think im all sorted now. got two mates coming with mr tomorrow and iv had it to bit more time this year then i care to ...

Throw up a photo of your problem... There maybe some guys on here who can advise on a good fix... I would suspect if its just cracked and hasn't moved then a re weld would be in order with a bit of reinforcement.. Probably need to remove the knuckle and drive shaft from that side and wipe out the ...

hi, my 60 series is a little more then broken. the front axle housing has cracked and is about to loss the wheel and steering knuckle. its not good. the main problem i have is that its had a spring over so the axle housing has been cut about and changed (it cracked at one of these welds). its going ...

just thought i would post a link for my photo site.
if you board have a look.
http://lukesergent.co.nz/

no sorry, not the bit thats part of the gear box

still have it

fingers crossed for tomorrow!!!

do you have to wait 28 days? iv read they can see it failed but not what for or where. i was just going to take it in tomorrow, to a little garage. only 3 days after the last one at VTNZ.

got it booked in to the garage across the road from work tomorrow. just hope they dont pull me up but worth a go i think. ow and VTNZ also failed the inter cooler saying it needed to be certed as it could boost power but more then 20% but i questioned this and he went off for 10 minuets then come ...

the cert was done by some one else 7 years ago and i don't the paper work.
its going to cost lost to get recert but only $50 to get tested else where. i think its just VTNZ being to strict on 4X4s