What front brake lines are people using for a 2'' spring lift? or are custom made the go? what length if custom made?
Cheers
Dean

I took my standard sj413 steering shaft to an engineer and got the splines cut further down the shaft then cut the end off to the right length (cant remember exactly how much i took off)

Anyone? must be some lying around on a spare axle somewhere

Anyone know where i could get a bolt (or 2) for a Suzuki SJ413 hub seal?

Has a 12 mm head and m6 thread


Cheers
Dean

Ah ok, was wondering why Don and Ian had the same address on the certifier list

Cool cheers

Whos the best cert person to see around Chch at the moment? Looking to cert my SJ413 with a few bolt on mods

cool cheers will pm you

Hey guys,
I'm after a distributor housing for an 8v g16a as i managed to crack mine replacing the o'ring

Cheers
Dean

Or even 410 or samurai set? think they all fit

Hey team im after a set of seat runners for my sj413 both drivers and passengers. I'm in Chch.

Cheers
Dean

I'm now looking at getting a better welder as my 100amp gasless migs not great This one from BOC has caught my eye, m Anyone have any thoughts/experience with them? The only thing that worrys me is the 15amp plug but i could get an adaptor to a 10amp for home or I do have access to 15amp power for ...

Deano! I booked the truck in for monday for cert i need one too!!! (Must be for my masive horsepower increase!!) got the specs off Don Hoff they require a 50x5 full hoop within 150mm from front UJ behind transfer only on the rear driveshaft i have full spec sheet if you wana grab it from me? Also ...

Cheers for the replies but it still doesn't quite answer my question. I know when I repowered my Holden I had to have 2 hoops as the drive shaft is in 2 sections. What a pain that was. As the sj413 has a divorced transfer case does this make it a 2 piece driveshaft? so then i would need one for the ...

Getting near cert time on my sj413, just reading up about driveshft loops as il need one.
I know this is probably a dumb question but......
Just wondering what driveshaft it goes on? the rear or the gearbox to transfer one? or both?

Cheers Dean

Made up a full 2inch exhaust including headers for the sj, sounds much better now

^^ x2

Bloody well looked after truck thats going to make whoever buys it very happy
Hope it stays local so you can see it do what you intended

Twodiffs wrote: He can't do steering mods like it says at the start of this thread

So he can't do a power steering conversion using a bolt in kit? I see he can do categories 1A 1B 1C on the category list that include bolt in steering mods?

Certifier list: http://www.lvvta.org.nz/documents/suple ... ebsite.pdf

Cert categories: http://www.lvvta.org.nz/documents/suple ... gories.pdf

Who needs mud tyres or 4wd?

Ford power

Or does anyoe have a old oe they want to sell?

The ball joint at my pitman arm end of the draglink on my 413 is a bit buggered and now after rebuilding the swivel hubs, kingpins etc it seems to be showing a bit more slop with the extra resistance of working bearings and seals Anybody know if these are serviceable? can only find the entire ...

Thanks man thats awesome

Looking good Blake

Any chance of a couple of pics of what you're doing around the headlight bucket area? thats where im clipping and not too sure how to attack it

I have heard of someone doing the exact same thing you are doing to someone, pretty much screwed him over and he had to move home to his parents down country. I knew i had read a awesome thread on this somewhere. Have found it again, its on game planet. A intersting read if you have time http://www ...

Swamped wrote:They could be a BNT part?

Looks like i might have a ringing around session ahead

Or maybe i should bring forward my next lowrange offroad order as i see they sell them...

Hi guys,
Whereabouts would i be able to source some new kingpin shims for my suzuki sj413? pulled the knuckles apart in the weekend to rebuild it all and there had been a total of 3 in there and the kit i got doesn't have any.

Cheers
Dean

Picked up my balls and the grinder and started the guard chop on my SJ http://i1022.photobucket.com/albums/af348/dean_zuk/2013-04-06124400.jpg http://i1022.photobucket.com/albums/af348/dean_zuk/2013-04-06124422.jpg http://i1022.photobucket.com/albums/af348/dean_zuk/2013-04-06152138.jpg Still have to ...

Keep. I often read on here but don't post much as i don't normally have alot of tech knowledge to add, but when i do post/start a thread i try and make it clear what i want to know, and make a clear conclusion so it can be usefull if found in a search. Might help if people think about how a thread ...