Hi, 3YE motor and ecu. Was running, new clutch and pressure plate 10,000 ks ago. Includes Ecu, rebuilt high output alternator, electronic distributor, airflow meter and g52 bellhousing.Has a slight knock when cold, disappears when warm, doesn't use oil or water. Pickup in Katikati. $350. Ph John ...

Hi,
Can anyone point me in the direction of a steering extension clamp?
I'm still trying to cert my 3RZ conversion and they have told me I have to get one for the bodylift.
I had a quick search and found some in Oz for $195 au and that was about it.
Is anything available locally?
Cheers

Hi Paul,
I dropped my drive shaft at a local engineering shop today to get a 25mm spacer made, so I'm sorted. Thanks for your offer.
Cheers,
John

Hi,
I need a rear driveshaft from a LN/KZN 130 to finish my YN 60 3RZ swap if anyone has one.
The length I need is 1055mm from the back of the rear universal flange to the front of the spline shroud.
I'm in Tauranga.
Thanks,
John

Mmmm I have those bits, I'll look at it tomorrow. Cheers

I have the bent pipe, good to know the 3Y radiator works. Re the Evap can is your solenoid remote or part of the top of the evap can.
I see some 3RZ's have remote solenoids. I have been chasing cans with fixed solenoids but without luck.

Hi Stu, thanks for looking. I located some mounts, I'll cut them off on the weekend, they are expensive but at least I can put the motor in now. I have the tank, pump and lines already in place from my previous 3YE conversion. I have re-routed the lines to the passenger side. The xmember is done. I ...

Hi,
As above I am looking for LN series engine mount brackets for my 3RZ conversion. Does anyone know of an old LN chassis I could cut these off?
I am in Tauranga.
Thanks

Thanks,
Just got to find the LN 130 driveshaft, the LN 46/65 engine mounts, an Evap canister and its ready to start.
Cheers

A couple more questions,
Do I have to use the charcoal evap canister cos I don't have one?
Is the bodylift essential to clear bellhousing?
Cheers

No worries Stu.
I've been trapping in the Urewera and flew out a few days ago..
I'm moving a bit of gear around and will pull the old motor out next week.
I'll try to take photos and will post it up when its done.
Cheers

Hi,
Does anyone have a speedo cluster for a YN 60 they would sell?
Mine has shorted out.
Thanks

Thanks Stu,
I can sort the bits before I start so it should be relatively easy.
Thanks for your help.
John

Hi Stu, So I had a look under the lux and can see what you explained. Oh, the lux is a YN 60 not 65 as stated with a G52 trans. Re the front drive-shaft it looks as though it will require shortening the 45mm the engine is moved forward? Re the exhaust did you do a cross-over to the original L/H side ...

Cheers Stu that's gold, I'll have a look at it in the daylight and it should be obvious.
Thanks,
John

Hi, I have a 3RZ engine with clutch and bellhousing to install in my lux. I have browsed the 3RZ threads but am still unsure of a couple of things about the engine mount mods. Big Stu used LN mounts and also moved the engine forward 40mm but I couldn't work out what he had done with the gearbox ...

Sold Thanks

Got one off TM, Cheers

Katikati 0275435583

A rolled 91 or 92 Prado 5 speed, drove it home after the roll and drove steered as normal.
Complete apart from engine and wheels. $700 obo

Does anyone have a starter motor they would part with? Mine died yesterday, the armature is shot.
Thanks

Looking for door key and barrel also ignition barrel and key? My young fella lost them.... in town....partying with his mates

Thanks for the offer, I pulled the switch to pieces and found one of the contacts had some rubbish in it, cleaned it out and it seems to be working now.
If it craps out again I will get back to you.
Cheers

Thanks I will pull it off and check tomorrow.

Does anyone have a light indicator cluster switch to suit an 1985 Hilux they can part with, have failed a WOF cos the high beam won't work.
Thanks

Now on TM, Thanks..
Sold

$475 take it away?

Just remembered I forgot these details as well.
Tauranga-John 0275435583
Cheers

Hi guys,
I bought a dereg 2l V6 auto 2 dr runner a while back for a project. I no longer have the time etc for it and have no interest in wrecking it.
I paid $575 for it, if anyone is interested at that price FIBD .
Cheers
Forgot, screen is busted and needs drivers door glass

Thanks for your advice, I have the Haynes manual 92735, I will have to learn to read wiring diagrams.
Re the colour codes, when a wire is designated B for instance does it mean Black or Blue ? L ?
Cheers