Hi,
Wondering if anyone has some EGR blanking plates or know where to get?
I could make some up, but just checking if there is anywhere that might do them ?
Cheers
Search found 131 matches
- Mon Aug 12, 2019 3:11 pm
- Forum: Toyota
- Topic: 1hd-ft EGR blank plates
- Replies: 0
- Views: 10303
- Sat Jun 29, 2019 3:25 pm
- Forum: Toyota
- Topic: Land cruiser 80 series- AWD or 4WD?
- Replies: 3
- Views: 4046
Re: Land cruiser 80 series- AWD or 4WD?
I've just seen this: http://www.off-road.com/trucks-4x4/tech/toyota-land-cruiser-cdl-switch-install-review-53202.html "The Land Cruiser runs with an open center differential in high range (4HI). When low range (4LO) is engaged, the center differential locks, giving a true 50/50 power split to f...
- Sat Jun 29, 2019 2:29 pm
- Forum: Toyota
- Topic: Land cruiser 80 series- AWD or 4WD?
- Replies: 3
- Views: 4046
Re: Land cruiser 80 series- AWD or 4WD?
I've been researching this for two days now and I still don't have a definitive answer. 1) Is the VC only on the t-case's rear output ? 2) Does the center diff AND the VC lock when in low (or you've installed a CDL switch) or does the VC not lock up ? If so, it's AWD but with a LSD effect on the rea...
- Fri Jun 28, 2019 7:03 pm
- Forum: Toyota
- Topic: Land cruiser 80 series- AWD or 4WD?
- Replies: 3
- Views: 4046
Land cruiser 80 series- AWD or 4WD?
But if a noob question but I couldn’t easily find this out. I’m looking at a buying another land cruiser, this time a 80 series. It’s 1997 with the 1hdft No center diff lock. So does that means it’s AWD? What does the transfer box do In regards to the power front/back ratios or is it fully open? Tha...
- Mon Nov 27, 2017 2:32 pm
- Forum: Having problems?
- Topic: 92 Terrano TD27t noise (can't figure it out)
- Replies: 5
- Views: 4736
Re: 92 Terrano TD27t noise (can't figure it out)
Update. Turned out the transmission filter was blocked and the trans lost pressure.
New filter, new fluid. Noise gone. Hopefully no long term damage!
New filter, new fluid. Noise gone. Hopefully no long term damage!
- Tue Nov 07, 2017 12:42 pm
- Forum: Having problems?
- Topic: 92 Terrano TD27t noise (can't figure it out)
- Replies: 5
- Views: 4736
Re: 92 Terrano TD27t noise (can't figure it out)
Whining noise still there. Might be coming from gearbox area. What tests can we do to isolate if it's something in the gearbox ? (I'm suspecting maybe a input shaft bearing?) Also could it be a spun mains bearing in the motor ? (what do they sound like when they're toast?) Torque convertor ? (Do the...
- Wed Nov 01, 2017 10:18 am
- Forum: Having problems?
- Topic: 92 Terrano TD27t noise (can't figure it out)
- Replies: 5
- Views: 4736
Re: 93 Terrano TD27t noise (can't figure it out)
How will that stop the turbo from spinning?
- Mon Oct 30, 2017 10:27 am
- Forum: Having problems?
- Topic: 92 Terrano TD27t noise (can't figure it out)
- Replies: 5
- Views: 4736
92 Terrano TD27t noise (can't figure it out)
Hi guys, thought I'd ask as there's loads of people with TD27's here... Recently a mate's Terrano has started a whining noise that changes with RPM - it's at it worse @ 2.5 - 3.5k RPM. It's auto. It's noticeable a lot more when it's cold. It's louder when you're accelerating under load in gear (so r...
- Wed May 20, 2015 2:31 pm
- Forum: Drivetrain / Suspension
- Topic: Legal limits for suspension lift
- Replies: 17
- Views: 16668
Re: Legal limits for suspension lift
Here it is: ========================== ========================== Coil springs fitted to low volume vehicles must not be modified for the purpose of changing the vehicle’s ride height unless The spring is modified by a recognised spring manufacturer and the configuration of the modified spring ends ...
- Wed May 20, 2015 2:27 pm
- Forum: Drivetrain / Suspension
- Topic: Legal limits for suspension lift
- Replies: 17
- Views: 16668
Re: Legal limits for suspension lift
There a lot of hairy fairy words used but it's all here.
Print it out and leave it in your trucks... if a cop questions it start reading it to him/her/it
http://www.lvvta.org.nz/documents/stand ... ystems.pdf
Print it out and leave it in your trucks... if a cop questions it start reading it to him/her/it
http://www.lvvta.org.nz/documents/stand ... ystems.pdf
- Tue Dec 16, 2014 11:11 am
- Forum: 4WD Parts
- Topic: Trademe auctions (interesting TM auctions)
- Replies: 1524
- Views: 301112
- Mon Sep 29, 2014 3:03 pm
- Forum: Petrol Engines and Modifications
- Topic: Holley or Q'jet?
- Replies: 12
- Views: 2833
Re: Holley or Q'jet?
Here's what I usually do (if I can't be bothered) - If the QJet doesn't run nicely then slap a new or good Holley (600 vac sec) on it and it will just go... most likely will guzzle gas... but hey it's a V8 right ?
- Mon Sep 29, 2014 3:01 pm
- Forum: Petrol Engines and Modifications
- Topic: Holley or Q'jet?
- Replies: 12
- Views: 2833
Re: Holley or Q'jet?
A new Holley out of the box will work... It might need minor tweaking, but generally it will be fine for a 350. Go Holley if you can't be bothered with a decent carb :wink: :wink: :wink: On the other hand QJet's are a great carb. They are "on demand" and will draw as much fuel as they need...
- Tue Sep 23, 2014 10:38 am
- Forum: Petrol Engines and Modifications
- Topic: Needing a carb for a 3f
- Replies: 5
- Views: 1395
Re: Needing a carb for a 3f
I bought one for my old 60 series from ebay. Cost about $250 inc postage.
For example: http://www.ebay.com/itm/New-Carburetor- ... 4b&vxp=mtr
For example: http://www.ebay.com/itm/New-Carburetor- ... 4b&vxp=mtr
- Tue Aug 05, 2014 4:36 pm
- Forum: Drivetrain / Suspension
- Topic: Brake pedal creeping to floor
- Replies: 10
- Views: 1855
Re: Brake pedal creeping to floor
Probably the slave cylinder, that what it was for me.
- Fri Jul 25, 2014 7:53 pm
- Forum: Mitsubishi
- Topic: What size tyres will fit a stock height k96 challenger
- Replies: 5
- Views: 1141
Re: What size tyres will fit a stock height k96 challenger
32"s fit, 33"s rub with a normal offset. Lots of cutting and lifting to fit 33"s with -44 offset
- Fri Jul 11, 2014 9:51 am
- Forum: Fish'n
- Topic: outboard hard to start
- Replies: 8
- Views: 5862
Re: outboard hard to start
Proper procedure; squeeze the primer bulb first untill firm. Then push the key switch in for choke and rotate to the start position simultaneously. It will crank right up. Of course this is the cold crank procedure only. Once it's warm you don't touch choke, just turn the key, let it idle for min th...
- Fri Jul 11, 2014 9:40 am
- Forum: Fish'n
- Topic: outboard hard to start
- Replies: 8
- Views: 5862
Re: outboard hard to start
my old outboard did the same. Turns out it was the way I was starting it. When it's warm, how do you start it? If it starts fine when warm but dies under a load will it also die you don't turn off and go slow or idle then give it the boot again? If so sounds fuel related, could even just need an idl...
- Fri May 02, 2014 7:12 pm
- Forum: Toyota
- Topic: 1KZ-TE starting like a pig
- Replies: 11
- Views: 4657
Re: 1KZ-TE starting like a pig
Curious as to how long glow plugs should last?
- Tue Apr 29, 2014 4:42 pm
- Forum: Stolen / Lost and Found
- Topic: Stolen......Valiant Ute. Wellington.
- Replies: 9
- Views: 5332
Re: Stolen......Valiant Ute. Wellington.
TheDarkSide wrote:Ute has been found..........it is a little worse for wear..........but not half as bad as the scrots who took it
Ooo tell us the story! It's awesome when you catch the scum f****s like that!
- Tue Apr 29, 2014 10:28 am
- Forum: Drivetrain / Suspension
- Topic: locked front diff
- Replies: 35
- Views: 7352
Re: locked front diff
x3 Weld it! It will be awesome.
- Mon Apr 28, 2014 4:43 pm
- Forum: Drivetrain / Suspension
- Topic: locked front diff
- Replies: 35
- Views: 7352
Re: locked front diff
So wait... re-read his first question.
Let's say he welds the front diff... and is in 2wd and the hubs are open (free) then each wheel can move freely correct ?
Engage 4wd + lock hubs, then he'll have a locked diff.
Correct ?
Let's say he welds the front diff... and is in 2wd and the hubs are open (free) then each wheel can move freely correct ?
Engage 4wd + lock hubs, then he'll have a locked diff.
Correct ?
- Sun Apr 20, 2014 7:33 pm
- Forum: Petrol Engines and Modifications
- Topic: Quadrajet carby help ?
- Replies: 21
- Views: 4031
Re: Quadrajet carby help ?
You sure it's a problem with the carb? Do you have an electronic dissy?
I've had a bit to do with holleys and quaddies. Pm me if you need some help.
I've had a bit to do with holleys and quaddies. Pm me if you need some help.
- Mon Mar 31, 2014 3:08 pm
- Forum: Diesel Engines and Modifications
- Topic: 1kz te What mods can I do?
- Replies: 44
- Views: 64438
Re: 1kz te What mods can I do?
I run my cooler in series after the trans and before the in radiator cooler. This is done for two reasons 1. so if the trans gets hot most of the heat is dropped before the radiator 2. if the oil out of the cooler is cold the water temp will help keep it warmer Maurice Hmm I did the same thing and ...
- Mon Mar 10, 2014 1:48 pm
- Forum: Toyota
- Topic: Thinking of towing with a 1KZTE?....Think again…
- Replies: 58
- Views: 20947
Re: Thinking of towing with a 1KZTE?....Think again…
I change my driving style to the EGT's. I've towed my 1 ton jetboat over the same places in my 1993 prado 1kz-te with 300,000k's on the original head. Obviously I've kept the cooling system tip top, but like Fitzy says you have to drive to the EGT's. Sometimes I'm going voer a hill @ 30km/h... must ...
- Tue Mar 04, 2014 3:44 pm
- Forum: Toyota
- Topic: Thinking of towing with a 1KZTE?....Think again…
- Replies: 58
- Views: 20947
Re: Thinking of towing with a 1KZTE?....Think again…
I love this thread. It's probably the most truthful thread on overheating 1kz's out there!
Summary: 1KZTE's regularly crack heads
Why: Various reasons!
Fix: All the usual preventative stuff
Conclusion: Toyota almost made an awesome engine!
Summary: 1KZTE's regularly crack heads
Why: Various reasons!
Fix: All the usual preventative stuff
Conclusion: Toyota almost made an awesome engine!
- Fri Feb 21, 2014 1:40 pm
- Forum: Toyota
- Topic: KZJ78 Auto issue in low range.
- Replies: 13
- Views: 1808
Re: KZJ78 Auto issue in low range.
Agree, low range is exactly that in these boxes and yes the change from 1st to 2nd can sometime be a bit harsh, but it's not that bad! I hardly use low range but when you do it's a good experience especially going down steep inclines.
- Fri Jan 24, 2014 10:03 am
- Forum: Petrol Engines and Modifications
- Topic: 91 vs 95
- Replies: 12
- Views: 3109
Re: 91 vs 95
you can also add octane booster if your still worried. Octane booster is a total myth, there have been many test conducted. Check it out: http://www.youtube.com/watch?v=2jbcCr2ll3c Also, 91 vs 95 is not going to make much of a difference. Don't worry about it unless you have an old V8 pushrod engin...
- Mon Dec 30, 2013 9:13 pm
- Forum: 4WD Parts
- Topic: WTB: Holley 390 or 450
- Replies: 0
- Views: 282
WTB: Holley 390 or 450
Hey fellas,
Does anyone have a Holley 390 or 450 out there?
Cheers!
Tim
Does anyone have a Holley 390 or 450 out there?
Cheers!
Tim
- Fri Dec 20, 2013 9:21 am
- Forum: Diesel Engines and Modifications
- Topic: 1KZ-TE Echause Gas Tempratures
- Replies: 21
- Views: 5948
Re: 1KZ-TE Echause Gas Tempratures
Modified the viscous fan last night. Wow! what a difference.
It's all in the valve adjustment. It's on 80% of the time now. Bit loud, but I don't really care!
Might re-adjust it after summer again so it's only on when it's HOT!
It's all in the valve adjustment. It's on 80% of the time now. Bit loud, but I don't really care!
Might re-adjust it after summer again so it's only on when it's HOT!