Hi Folks

Does any body have or know where I can get an off set fairlead for plasma winch rope?

My PTO unit on the side of my gq gearbox only had sealer between it and the gearbox. Should it have a gasket or not?

Thanks, time to hunt for some wrx seats

Thanks guys will have a look into it. If any body knows where I could pick up some reasonably priced wrx seats from a 2 door let me know.

Hi
Has anybody out there replaced their gq front seats for something different with a bit more support. I don't won't a full on race seat but a bucket that will drop in with not too much trouble.
I have a swb so won't a seat that flicks forward so passengers can get in the back.

I got mine from a conveyor belting place in East Tamaki, I think Greenmount Drive. It was an off cut, cost me about $20.00 a few years ago.

doddzee wrote:$200 is about right, I have a gearbox and transfer for sale $550.

Hey Doddzee, if you don't sell that gearbox soon I might be keen, I am pulling mine out to do bearings but if it is too expensive to do might be better if I bought a good second hand one.

Definitely saves space parking it like that. Well done.

Yep I'm a bit like you, can't bare to part with the dollars, I am half Scottish so that doesn't help.

Is it normal to need to lengthen the drive shaft when going to a 3inch lift?

Does anybody know where I could get a cheap 3 inch exhaust made up for the Saf in Auckland or should I buy some bends and do it myself?

I think it is a sub with wind down windows?

That stuff looks awesome do you know anybody that has used on their truck?

Hi CD I rotated the end plate so that the filler plug was near the top, remove filler plug and replace with hose connection and run hose to bottom of reservoir. Remove breather and replace it with a fitting and run hose from breather to top or half way up reservoir. The oil won't necessary circulate ...

Yep, what he said

O for Oarsome

Yep

I'm in Botany too. ha ha ha

I have one for pumping up my tyres, it gets really hot at the fitting and even the air hose close to the compressor gets really hot. When mine is hot I leave it out of its bag afterwards and away from everything else till it cools down.

I cut mine to be level with the lower edge of the rear panel under the rear doors. If you want to PM me I can give you a call or send you some photos.

Hi Ant I have a shorty with a guard chop, it has a 2 inch long wheel base lift in the back which pops it up to about a 3 cause the shorty has less weight over the rear than the LWB. I cut the guards with a very thin cutting wheel on an angle grinder then made cardboard templates for the holes. Use ...

Go the Nisssann!!!!!!!!!!!

Hi Jungle
What do we need to do if we are coming as part of the crew for one of the competitors?

I'm in Auckland

Hi Folks The bearings in my Saf's manual gearbox have been noisy for a while now so it is time to replace them, hopefully when I pull it down there will be no shaft ware. Does anybody know a good supplier to get a bearing kit or individual bearings from, alternatively a cheap place that rebuilds ...

I put one piece windows into the back of my SW Safari, my local glass guy in Howick got some glass(must be same standard as that removed to meet wof regs) cut to the right size for me, I did however give him a template to cut them too. Made the template out of old core flute plastic signage material ...

Looking good and I bet that is just the oil cooler for the power steering.

Got my rocker gear back together last weekend on the Saf and got a warrant yesterday. "Back on the road again"

Any ideas on dates for the Rotorua winch challenge?

Thanks guys for all your help and advice, I have had a good look at the parts I have and the rockers will go another turn so I just need a new rocker shaft which I have ordered.