Got a 1JZ-GTE in my LJ71 Bundy, Alot of work but worth it in the end, Got motor and box (R154) out of a supra and put the cruiser tranz case on the end, Half way though a single turbo swap so hope for more power LOL . The manual R154 box is from the same family as the R151 box that was in the ...

suck if you do send it back and they strip it they might just say that you did the damage and tuff luck . might even end up with a bill for the reconditioners labour but still no motor Yeah was a bit worried about something along those lines happening, Should do as WJW did and see what can be done ...

Yeah its from a importer and under warrenty but he wont replace it yet, he wants me to send it to him and they will stip it down send it to a engine recon place to find out what if anything is wrong then decide to fix/replace or refund, had motor for 5 mths but was under warrenty for 3 mths and its ...

LOL yeah did get i bit hot. Talked to engine importer and hes guna be no help, hell he didn't half lose the plot so i'm not holding my breath for another motor. Hoping its not to bad and theres still some diesel in the tank becouse it only gives one buff of blue when i hit the gas and white smoke ...

Hi Tony, Yeah can wait to get out there again way beter than with the old diesel in it LOL, The PCV valve wasn't hooked up to the intake i had it on a after market breather. It only smokes when up to running temp. Had a local supra guru come and have a look and said it maybe valve guides???? , found ...

Will have a look tomorrow.there is a little oil after the turbos but before the inter cooler piping,ran it up without turbos and still smoked but will have a better look tomorrow.

Hi Steve Empted the tank with the drain plug, chucked 20ltrs in then left it with the pump going to mix the fuel up for 30min,drained then two full tanks and just started the 3rd. Drained half the 2nd tank today and put it into my falcon that was almost out of fuel and no smoke so made me think ...

Hi all, just finished doing my supra swap into my LJ71, its running great other than the smoke out the tail pipe.Just thorght i would check with other people that have gone from diesel to petrol how long it was before it cleared up as the supplyer of the motor say theres nothing wrong with it but ...

Hope to get another one to tag along with any luck to make it four from Taupo

Make that 3 wagons from Taupo,cruiser and two surfs

sorry that was supposed to be Brian not pete

Hi pete,count me in for the 23rd

count me in for the 23rd as well

Yep i would be keen to at a later date

Will be keen,just sorting out the last few things on the 1JZ-GTE motor swap.........

Going to run the manual ECU computor and if i need anymore power (2LT compared to 1JZ-GTE hahahaaa!!!)i will pack the wastegates out a bit to up the boost,running the standard turbo clutch and pressure plate (mate told me how many lbs they were but to many woodys tonight to remember LOL),have read ...

Ive got the R151 box in my cruiser and the R154 is the same on the out side,so the bellhousing bolts on just getting either the input shaft from the R154 onto the R151 or the output shaft from the R151 onto the R154,yeah they look impresive on paper but having never driven one yet wont know for sure ...

Small world,Just started throwing a 1JZ-GTE into my LJ71 Bundera,only problems so far aside for engine mounts is the shorter input shaft on the R151 gear box Luckly i got a R154 box with the longer input shaft so geting the short output shaft from the R151 put onto the R154.........Hope it works LOL ...

Dont think new motor will be up and running by then, but keen for another one when it is

Will be there if i get the 1jz sorted in time

Will be there in my landcruiser plus a mate (Taka) in his surf.

count me in if you dont mind newbies tagging along another wagon from Taupo will more than like follow me over as well if thats cool.....

Hi nigelb, I had this problem with my chinese 12v winch and it was the earth brushes had rusted between brush mounting plate and main body if that makes sense,solenoids would work and power would get to winch but no go,just drilled out the rivets that hold the brushs in cleaned them up put small ...