my 80 died

For all Toyota related topics ie. Hilux, Cruiser topics
User avatar
adogg
Hard Yaka
Posts: 118
Joined: Fri May 25, 2007 12:00 pm
Location: Taupo

Re: my 80 died

Post by adogg »

fuel tank prolly vents through the cap ,take it off and see if it makes a difference
yeah i own a few cruisers
hdj81
fj55
fj40
User avatar
skid
Tyre Man
Posts: 6311
Joined: Thu Oct 06, 2005 12:00 pm
Location: WELLINGTON-0272417757
Contact:

Re: my 80 died

Post by skid »

adogg wrote:fuel tank prolly vents through the cap ,take it off and see if it makes a difference



thats the cap that you munted :roll: :roll: :roll: :roll:

maybe thats the problem :shock: :shock: :shock:
80 Series on 35" creepies, manual with twin factory lockers.
0272417757

*CHILLAX BRO.*
User avatar
curly12
Hard Yaka
Posts: 1335
Joined: Fri Mar 02, 2007 12:00 pm
Location: Whangarei or there abouts!!

Re: my 80 died

Post by curly12 »

skid wrote:
adogg wrote:fuel tank prolly vents through the cap ,take it off and see if it makes a difference



thats the cap that you munted :roll: :roll: :roll: :roll:

maybe thats the problem :shock: :shock: :shock:


You can just see the penny drop, can't you?? :roll: :roll: :roll: :roll: :roll: :roll: :roll: :roll:
Growing old is compulsory, growing up is optional

Farken homeless..................................
User avatar
pagar
Hard Yaka
Posts: 325
Joined: Wed Feb 13, 2008 9:58 am

Re: my 80 died

Post by pagar »

checck primer pump is at the top of its travel and start engine, rev from throttle body and watch the primer pump if it sucks down you have a fuel blockage pre filter (most likley deisel bug) remove filter and empty into a white container to check colour, if it has a blackish grey coulor you have the bug. clean filter in petrol and replace fill tank with fresh fuel and a anti bacterial agent Morey's one works well. no point replaceing filter till you have run a couple of tanks of additive through cause it will only block up new one. always keep your tank as full as posible to reduce growth. no coulor change, blow line back to tank (low pressure no more than 30 psi) and get someone to listen for bubbles. if the primer does not drop remove return line from tank and feed from filter to pump, put pump end in a container and blow out at low pressure check flow. do not be tempted to use high pressure as you can damage seals. if no blockages your pump may have failed but I would go with the above first. hope that helps. :( Cheers
If you follow me in the bush you must be mad cause I'm plain CRAZY !!!

1987 BJ74, 13BT, Auto, 35" Wranglers, 80mm Suspension Lift, 2" body lift, LSD rear, ARB Front Locker, PTO, Lots of Steel and a Go Hard Driver.
User avatar
adogg
Hard Yaka
Posts: 118
Joined: Fri May 25, 2007 12:00 pm
Location: Taupo

Re: my 80 died

Post by adogg »

skid wrote:
adogg wrote:fuel tank prolly vents through the cap ,take it off and see if it makes a difference



thats the cap that you munted :roll: :roll: :roll: :roll:

maybe thats the problem :shock: :shock: :shock:


that i munted wtf are you on about? has your 80 got the steel cap or the plastic cap? steel cap vents inside the left rear guard ,plastic cap vents through it self,i vaguely remember trying to fit your 80 cap to your 40 but i think i modifyed your 40 to suit that cap :roll: :roll: :wink: lol, chuck a new filter at it,while your at it give it a oil change too,it`ll love you for it
yeah i own a few cruisers
hdj81
fj55
fj40
User avatar
Jerry
Yes Dear
Posts: 8325
Joined: Tue May 30, 2006 12:00 pm
Location: Wellington 027 479 2417

Re: my 80 died

Post by Jerry »

put some diesel in it too :lol: :roll: :D
70 series prado (KZJ78) and 90 Series Prado (KZJ95)
User avatar
skid
Tyre Man
Posts: 6311
Joined: Thu Oct 06, 2005 12:00 pm
Location: WELLINGTON-0272417757
Contact:

Re: my 80 died

Post by skid »

Jerry wrote:put some diesel in it too :lol: :roll: :D



Image

BITE ME







adogg wrote:
skid wrote:
adogg wrote:fuel tank prolly vents through the cap ,take it off and see if it makes a difference



thats the cap that you munted :roll: :roll: :roll: :roll:

maybe thats the problem :shock: :shock: :shock:


that i munted wtf are you on about? has your 80 got the steel cap or the plastic cap? steel cap vents inside the left rear guard ,plastic cap vents through it self,i vaguely remember trying to fit your 80 cap to your 40 but i think i modifyed your 40 to suit that cap :roll: :roll: :wink: lol, chuck a new filter at it,while your at it give it a oil change too,it`ll love you for it



yup , after you manipulated my cap to fit my 40, its never been the same.





OK, new fuel filter in today, seems a bit better and cleaned up the dodgy battery terminal, which seemed to help a little bit.

yup when money allows, an oil change will eventuate






if anybody is wrecking a 80 and wants to give skiddy some parts, then I need a fuel cap, a speedo cable and some other minor items, like the wipers
80 Series on 35" creepies, manual with twin factory lockers.
0272417757

*CHILLAX BRO.*
User avatar
Steve_t647
Hard Yaka
Posts: 998
Joined: Wed May 17, 2006 12:00 pm
Location: Christchurch City, In front of the computer

Re: my 80 died

Post by Steve_t647 »

You havent got diesel at a remote petrol station recently, you may want to put some diesel bug killer through it. If the diesel darker than usual?
Legal disclaimer: Any information I may have provided is worth exactly what you paid me for it.
User avatar
Jerry
Yes Dear
Posts: 8325
Joined: Tue May 30, 2006 12:00 pm
Location: Wellington 027 479 2417

Re: my 80 died

Post by Jerry »

Sig was wrecking one a whilst ago, he hasn't got those parts?
70 series prado (KZJ78) and 90 Series Prado (KZJ95)
User avatar
skid
Tyre Man
Posts: 6311
Joined: Thu Oct 06, 2005 12:00 pm
Location: WELLINGTON-0272417757
Contact:

Re: my 80 died

Post by skid »

Jerry wrote:Sig was wrecking one a whilst ago, he hasn't got those parts?



I think I already asked

besides he wrecked a bit of that 80 with a sabre saw :roll: :roll: :roll: :roll: :shock: :shock: :shock:

I was told
80 Series on 35" creepies, manual with twin factory lockers.
0272417757

*CHILLAX BRO.*
User avatar
curly12
Hard Yaka
Posts: 1335
Joined: Fri Mar 02, 2007 12:00 pm
Location: Whangarei or there abouts!!

Re: my 80 died

Post by curly12 »

Did you get this sorted skid??
Growing old is compulsory, growing up is optional

Farken homeless..................................
User avatar
skid
Tyre Man
Posts: 6311
Joined: Thu Oct 06, 2005 12:00 pm
Location: WELLINGTON-0272417757
Contact:

Re: my 80 died

Post by skid »

curly12 wrote:Did you get this sorted skid??



did I make to beer bach for a beer


does a beer shit in the woods


is the pope gun shy



















still needs a oil n filter, but OK otherwise
80 Series on 35" creepies, manual with twin factory lockers.
0272417757

*CHILLAX BRO.*
User avatar
pagar
Hard Yaka
Posts: 325
Joined: Wed Feb 13, 2008 9:58 am

Re: my 80 died

Post by pagar »

I'm sure bears do shit in the woods but who knows if the pope is gun shy, for all I know he may well have an m16 under that baggy robe :) so what was wrong with it?
If you follow me in the bush you must be mad cause I'm plain CRAZY !!!

1987 BJ74, 13BT, Auto, 35" Wranglers, 80mm Suspension Lift, 2" body lift, LSD rear, ARB Front Locker, PTO, Lots of Steel and a Go Hard Driver.
User avatar
Sadam_Husain
Angry bird
Posts: 5164
Joined: Mon Feb 20, 2006 12:00 pm
Location: WELLINGTON

Re: my 80 died

Post by Sadam_Husain »

pagar wrote: so what was wrong with it?


I dont think he actually knows :oops: :oops:

It seemed to be going ok round the south coast to the beer brothers beer bach the other night so maybe it was just a crook fill of diesel?
User avatar
Jerry
Yes Dear
Posts: 8325
Joined: Tue May 30, 2006 12:00 pm
Location: Wellington 027 479 2417

Re: my 80 died

Post by Jerry »

He must have put Diesel in it :D
70 series prado (KZJ78) and 90 Series Prado (KZJ95)
User avatar
skid
Tyre Man
Posts: 6311
Joined: Thu Oct 06, 2005 12:00 pm
Location: WELLINGTON-0272417757
Contact:

Re: my 80 died

Post by skid »

Sadam_Husain wrote:
pagar wrote: so what was wrong with it?


I dont think he actually knows :oops: :oops:

It seemed to be going ok round the south coast to the beer brothers beer bach the other night so maybe it was just a crook fill of diesel?



true, I don't know. I'm not even a mechanics ass, as previously mentioned. :roll:

We replaced fuel filter and bled system and now is fine. 8) 8)

I don't think it was crap fuel as the old filter was fairly clean, but due to running it down to the fuel light for months and running out a few weeks beforehand, I believe it just piced up an air blockage that needed bleeding out.

Sometimes it still skips a beat when you're cruising along, but I'm sure the injectors need doing as it seems to be a hairy start on about 5 cylinders for a second, so does anyone know of a really good injector cleaner for diesels :?: :?:

and another thing, it smokes like a bastard when cold, I mean really smokes, WHY :?: :?:
80 Series on 35" creepies, manual with twin factory lockers.
0272417757

*CHILLAX BRO.*
User avatar
MNC
Hard Yaka
Posts: 2100
Joined: Sun Apr 02, 2006 12:00 pm
Location: Close to (wishing I was closer to) the Puhoi Pub!

Re: my 80 died

Post by MNC »

skid wrote:
Sadam_Husain wrote:
pagar wrote: so what was wrong with it?


...and another thing, it smokes like a bastard when cold, I mean really smokes, WHY :?: :?:


Seals might be leaking allowing oil into the cyclinders while sitting. Once it has a chance to burn out the excess oil (after warming up) does the smoke go away?
Image
User avatar
tgaguy1
Hard Yaka
Posts: 746
Joined: Sat Dec 24, 2005 12:00 pm
Location: Tauranga

Re: my 80 died

Post by tgaguy1 »

MNC wrote:
skid wrote:
...and another thing, it smokes like a bastard when cold, I mean really smokes, WHY :?: :?:


Seals might be leaking allowing oil into the cyclinders while sitting. Once it has a chance to burn out the excess oil (after warming up) does the smoke go away?



Or the injector seals might be leaking allowing the cylinders to fill with diesel while it sitting at night. What colour is the smoke?
User avatar
skid
Tyre Man
Posts: 6311
Joined: Thu Oct 06, 2005 12:00 pm
Location: WELLINGTON-0272417757
Contact:

Re: my 80 died

Post by skid »

tgaguy1 wrote:
MNC wrote:
skid wrote:
...and another thing, it smokes like a bastard when cold, I mean really smokes, WHY :?: :?:


Seals might be leaking allowing oil into the cyclinders while sitting. Once it has a chance to burn out the excess oil (after warming up) does the smoke go away?



Or the injector seals might be leaking allowing the cylinders to fill with diesel while it sitting at night. What colour is the smoke?



yeah it seems to go away after a while.

Was it smoky round the beach the other night Sadam :?: :?: :?:


its a greyish white smoke
80 Series on 35" creepies, manual with twin factory lockers.
0272417757

*CHILLAX BRO.*
User avatar
adogg
Hard Yaka
Posts: 118
Joined: Fri May 25, 2007 12:00 pm
Location: Taupo

Re: my 80 died

Post by adogg »

grey white usually means excess fuel,maybe the pump needs a tweak on the cold start timer,or maybe a crook glow plug? you really need to keep up on the oil changes on that thing man specially with there reputation for big end bearings!!
yeah i own a few cruisers
hdj81
fj55
fj40
User avatar
skid
Tyre Man
Posts: 6311
Joined: Thu Oct 06, 2005 12:00 pm
Location: WELLINGTON-0272417757
Contact:

Re: my 80 died

Post by skid »

adogg wrote:grey white usually means excess fuel,maybe the pump needs a tweak on the cold start timer,or maybe a crook glow plug? you really need to keep up on the oil changes on that thing man specially with there reputation for big end bearings!!



yup, I know, coz my Taupo mechanic keeps telling me.

its gonna happen very soon

cheers bro
80 Series on 35" creepies, manual with twin factory lockers.
0272417757

*CHILLAX BRO.*
User avatar
Jerry
Yes Dear
Posts: 8325
Joined: Tue May 30, 2006 12:00 pm
Location: Wellington 027 479 2417

Re: my 80 died

Post by Jerry »

what ..... next year SKID :D
70 series prado (KZJ78) and 90 Series Prado (KZJ95)
User avatar
skid
Tyre Man
Posts: 6311
Joined: Thu Oct 06, 2005 12:00 pm
Location: WELLINGTON-0272417757
Contact:

Re: my 80 died

Post by skid »

Jerry wrote:what ..... next year SKID :D



Jerry, don't make me tell you like I had to tell Gordon about when you need to shut up
80 Series on 35" creepies, manual with twin factory lockers.
0272417757

*CHILLAX BRO.*
User avatar
adogg
Hard Yaka
Posts: 118
Joined: Fri May 25, 2007 12:00 pm
Location: Taupo

Re: my 80 died

Post by adogg »

skid wrote:
Jerry wrote:what ..... next year SKID :D



Jerry, don't make me tell you like I had to tell Gordon about when you need to shut up



yow!!! take that biatch!!! lol
yeah i own a few cruisers
hdj81
fj55
fj40
User avatar
Jerry
Yes Dear
Posts: 8325
Joined: Tue May 30, 2006 12:00 pm
Location: Wellington 027 479 2417

Re: my 80 died

Post by Jerry »

LOL ok he's had enough shyte about changing filters and oil :D I'm verry sowrry skiddy widdy :D
70 series prado (KZJ78) and 90 Series Prado (KZJ95)
User avatar
pagar
Hard Yaka
Posts: 325
Joined: Wed Feb 13, 2008 9:58 am

Re: my 80 died

Post by pagar »

man I changed out my oil ever 5000km do oil filter and deisel filter every 10,000k diff oils and air filter@20,000. I would say you have got deisel bug though cause of the way it went away with the change. remove your filter and blow 30 psi up the return pipe to the tank and you will probably see some black snot come out of the line to the pump. it will be worse cause your tank is always empty. :(
If you follow me in the bush you must be mad cause I'm plain CRAZY !!!

1987 BJ74, 13BT, Auto, 35" Wranglers, 80mm Suspension Lift, 2" body lift, LSD rear, ARB Front Locker, PTO, Lots of Steel and a Go Hard Driver.
Post Reply

Return to “Toyota”