rear springs for RUF 410

[chrome]

[chrome]

chucked these on today.... tow hook also
and found a leak in the radiator

[skid]

[chrome]

got the rope rails done today and the rear support bars for the tray

[chrome]

and some spotties

[Bolo]

Man this is looking awesome keep up the great work , so keen to see this in the mud

[chrome]

new radiator today,out of a mazda van got it in and plumbed in but its still running too cool if the fan is on at idle so it should be fine in the tracks, just gotta fit the timber deck then bleed the brakes and mount the fan switches and its good to go

[chrome]

deck on, new radiator and all wiring tidied up

[chrome]

hope this works

[UBZ]

hope this works

wobble wobble , vibe vibe vibe .
you will need to have that balanced or its going to chew transfer / diff bearings and universal joints

[chrome]

its pretty strait, and more than likely when i break shit i can change it for new stuff. this is still a budget truck...i dont want to be paying for anyone to do stuff for me if i can help it

[chrome]

got these cut out today, laser cut 6mm steel, not all sharp and pokey outey like the flat bar ones

[chrome]

new snorkel is about all i got done this week but at least i got it out for my first offroad excursion in it
i did run out of paint too.....

[You Get That]

Nice placement of the winch there
I like it.

[UBZ]

Feels mint ah finally gettin out for a drive, how well is the front end flexing with the RUF

[chrome]

yeah i was happy to be driving it, as for the change in flex im not too sure as id only been using it to thrash round the workshops this was the first time iv taken it out in the mud....
was good muddy fun

[chrome]

found some lights and relays this week

and bodgeyed up a tarp roof

[chrome]

now im thinkin

[Heath]

now im thinkin

Some bastard stole all the good bits and left you a pile of junk steel.

Tell ya what I'll get rid of it, so you dont have to look at all the "junk".

[chrome]

ha i wish, this is just a picture i found, looks like something im keen to try build on the cheep

[Heath]

ha i wish, this is just a picture i found, looks like something im keen to try build on the cheep

Be hellish uncomfortable to ride in as it is. And you'll need a few extra bits to make anything of it. Some "Bling" for a start.

I thought I had seen a similar central control arm setup somewhere in the interweb for Jeeps (and on a rock crawling hilux/surf on here too I think).

That front driver's side is interesting, allows for a bit of movement I guess.

[chrome]

ive had a bunch of landrover front suspension parts come my way so coils in the front is about to happen. just not sure about spring lengths and spring rates, anyone on here got any advice???

[Sadam_Husain]

ive had a bunch of landrover front suspension parts come my way so coils in the front is about to happen. just not sure about spring lengths and spring rates, anyone on here got any advice???

go back and ask your Father inlaw he'll know how to set it up

[chrome]

na its not from him someone on here mate

[UBZ]

ive had a bunch of landrover front suspension parts come my way , anyone on here got any advice???

Im a poor little zuki , ive had my rear choped off , my guards ripped out ,and know my owner wants to weld land rover parts onto me .

[chrome]

i only chopped out the RUST

[chrome]

this is basically how my shittas gonna roll only with standard disco arms, im getting the plates plasma cut out at work tomorrow hopefully and i want to get it done on sat
i might look at shaving the diff too, does anyone know how much i can take off?

[skid]

seriously dude, if ya gonna go to the trouble of coiling it

lux axles/diffs at same time

[chrome]

plenty of time for that later. and to swap in lux later will be a quick job for when i have more money and a new motor

[chrome]

my plates are all sorted and seem to fit all good. had a crack at building coilovers as well... i think they should work