terrano idler arm

terranoman31 · Post by **terranoman31** » Wed Apr 27, 2011 11:04 pm

hey everyone i managed to strengthen up my idler arm but now my idler arm bushes keep collapsing i think.... should i just get some brass ones made up instead of having factory plastic ones?

any ideas?

sibainmud · Post by **sibainmud** » Thu Apr 28, 2011 12:36 am

Silica Bronze is the way to go.
Factory plastic ones are better than the rubber/nolathane ones from BNT

Thrashed them out in 1 trip :roll:

How have you strengthened it?
I found my idler shaft had heaps of wear in it and caused the movement that flogged the bushes. I found that the thrust/sealing washers are supposed to crush a wee bit and provide support for the idler on the shaft.
Cheers,

terranoman31 · Post by **terranoman31** » Thu Apr 28, 2011 10:33 am

all i done was weld on a brace to the idler arm with 10mm plate prob over kill but it works lol gave it a thashing last weekend and it didnt move

might have to look into brass ones then

u13turbo · Post by **u13turbo** » Thu Apr 28, 2011 6:09 pm

terranoman31 wrote:all i done was weld on a brace to the idler arm with 10mm plate prob over kill but it works lol gave it a thashing last weekend and it didnt move might have to look into brass ones then

What tyres are you running? any torsion lift? I just got a brace for mine, but am now worried about buggering my brandnew draglink as iv heard they are weak in terranos and it'll be fucked within 3 trips....

terranoman31 · Post by **terranoman31** » Thu Apr 28, 2011 8:17 pm

im just running 31s atm but hoping to upgrade at some stage to 33s no torsion lift atm have had to take gearbox out to do front seal of the gearbox so might do a lift but brace on arm has worked so far and brace on the bolt that holds idler arm works well i have a new drag link aswell hasnt done anything to it so far and i dont think it will as the idler arm wont or shouldnt bend now but i do think its illegal to have anything welded to steering... i know naughty lol but sick of having to change idlers all the time out on trips..

hopw this helps...

u13turbo · Post by **u13turbo** » Fri Apr 29, 2011 12:06 am

terranoman31 wrote:im just running 31s atm but hoping to upgrade at some stage to 33s no torsion lift atm have had to take gearbox out to do front seal of the gearbox so might do a lift but brace on arm has worked so far and brace on the bolt that holds idler arm works well i have a new drag link aswell hasnt done anything to it so far and i dont think it will as the idler arm wont or shouldnt bend now but i do think its illegal to have anything welded to steering... i know naughty lol but sick of having to change idlers all the time out on trips..

hopw this helps...

Ok sweet as, brace for my idler is just bolt on no welding to the idler needed. hoping it'll be strong now.

terranoman31 · Post by **terranoman31** » Fri Apr 29, 2011 9:07 am

only thing is the arm will bend like mine kept doing dunno if its my driving or not but it will push drag link into chassis rail if arm bends

muddyhilux · Post by **muddyhilux** » Sun May 15, 2011 12:19 pm

realise the threads a bit old but made this up for brother n laws truck couple of weeks ago and just got pic sorted,steering a lot better now with new idler and brace

terranoman31 · Post by **terranoman31** » Sun May 15, 2011 12:21 pm

i have done this also and managed to bend the arm... so welded a gusset on arm stops it from bending

i know its not wof standard so just change it when i go for wof lol will put up pic when i can

have a look

terrano idler arm

terrano idler arm

Re: terrano idler arm

Re: terrano idler arm

Re: terrano idler arm

Re: terrano idler arm

Re: terrano idler arm

Re: terrano idler arm

Re: terrano idler arm

Re: terrano idler arm