26th 27th

coxsy · Post by **coxsy** » Sat Nov 26, 2011 11:53 am

Again, one James is 21 today,
fixed diesel leak from injector return line.
two, hit a commodore with the ute

pulled the grille and bumper a hammer and wooden block straightened the bent steel supports a few tec screws all back together like it was before

kbushnz · Post by **kbushnz** » Sat Nov 26, 2011 12:01 pm

coxsy wrote:James is 21 today

Happy Birthday James.... :mrgreen:

Looking at reorganizing the dash / dial layout...
Playing with the rear storage area... its coming along good.

Calvin

worzel · Post by **worzel** » Sat Nov 26, 2011 3:17 pm

went for a warrant straight through clean sheet way to go

Filthy4x4 · Post by **Filthy4x4** » Sat Nov 26, 2011 3:27 pm

Went out to hampton downs with sibainmud, lincooln, drurban, hiluxdan and luke (sorry dont know your ore name :lol:

) met up with Gary, had a chat about mudfest and went and tested out the place.

Its shaping up to be a decent event, looking forward to it.

Didnt get any photos as my cam spat the dummy.

Caleb

ClassicCruiserSpares · Sat Nov 26, 2011 3:40 pm

Flushed my power steer system and filled with new oil and is all working much better now, Took my winch out, Cleaned and accessed damaged parts from Reefton trip. Tomorrow will fit new parts and reassemble.

sibainmud · Post by **sibainmud** » Sat Nov 26, 2011 4:30 pm

uwshho wrote:Went out to hampton downs with sibainmud, lincooln, drurban, hiluxdan and luke (sorry dont know your ore name ) met up with Gary, had a chat about mudfest and went and tested out the place.

Its shaping up to be a decent event, looking forward to it.

Didnt get any photos as my cam spat the dummy.

Caleb

I did

More to come.

Great to meet Gary and have a look over the area before it gets shredded.
We looked at some holes,

There are some truck swallowing drains, the drag strip will wear in nice.
I will post what little footage on the Mudfest page

Cheers,

Noeyedeer · Post by **Noeyedeer** » Sat Nov 26, 2011 4:34 pm

uwshho wrote:Went out to hampton downs with sibainmud, lincooln, drurban, hiluxdan and LUKE (sorry dont know your ore name ) met up with Gary, had a chat about mudfest and went and tested out the place.

Its shaping up to be a decent event, looking forward to it.

Didnt get any photos as my cam spat the dummy.

Caleb

Filthy4x4 · Post by **Filthy4x4** » Sat Nov 26, 2011 4:39 pm

At least you got footage of it, dont think ive ever had my leg disappear so fast :roll:

mfrsr · Post by **mfrsr** » Sun Nov 27, 2011 6:49 am

cleaned Surf. lot of oil on the rear diff.... not a bad effort, i only lifted it two weeks ago and its already eaten the pinion seal. And i've only done like 15km.

tomsoffroad · Post by **tomsoffroad** » Sun Nov 27, 2011 9:12 am

mfrsr
Post subject: Re: 26th 27th

cleaned Surf. lot of oil on the rear diff.... not a bad effort, i only lifted it two weeks ago and its already eaten the pinion seal. And i've only done like 15km.

Lifting it shouldn't affect pinion seals :shock:

KIWI_TERRANO · Post by **KIWI_TERRANO** » Sun Nov 27, 2011 9:14 am

mfrsr wrote:cleaned Surf. lot of oil on the rear diff.... not a bad effort, i only lifted it two weeks ago and its already eaten the pinion seal. And i've only done like 15km.

Has it got diff breathers fitted?

They will be the issue more.... I had a 4inch lift never blew a seal in 50000km

Shane · Post by **Shane** » Sun Nov 27, 2011 11:58 am

Went to Waimac and watched the marthon jet boats racing.

This one had a Gas turbine engine approx 1300-1500hp,easy the fasted boat there by 15-20mph(reported it could do 130mph)super reliable and well go 100% all day,boat handled very well also.
He did get beaten on the up stream leg though by a 572ci big block(took a few more risks at a guess but didnt finish the down stream leg)

As much as I hate to say it,pretty hard for a combustion engine to keep up on shear performance/reliability(really only has 1 moving part)

Was a great day

Two V8's from the B class(?)the second boat did end up passing and put a good gap on first one.

lincooln · Post by **lincooln** » Sun Nov 27, 2011 12:26 pm

So while I was at the mudfest trial day yesterday, on my way out I hit something in the grass that almost stopped the zuk in its tracks. Thought it must have been a bit of dirt or concrete or something. Then had a look under it today while I was removing the sway bar properly and found the mangled mess of a cross member. On closer inspection the two skins are separating, it has bent into the A arm and is cracking the welds at the chassis too. Had to hit in the same place as it was once repaired before as it ha cracked along the same weld. Bloody tree stumps. :evil:

Also put a new steering wheel on as I almost broke my last one.

But now need to see if I can fix the x-member or if it will be cheaper and easier to get a new chassis or just turn it into a trailer truck. mhmm...

shovel · Post by **shovel** » Sun Nov 27, 2011 7:06 pm

Bought a cheap helmetcam so strapped it to the rollbar of my Bushwhacker and went a drive.Pictures good but sound is a bit crappy,think it doesn't like the v8 open headers :lol:

http://youtu.be/OjlReBHD52o

Caleb · Post by **Caleb** » Sun Nov 27, 2011 7:27 pm

Went to the muddplug @ the club grounds down here, was a awesome day out!

mfrsr · Post by **mfrsr** » Mon Nov 28, 2011 12:38 am

tomsoffroad wrote: Lifting it shouldn't affect pinion seals

it's got a big silly lift. std suspension arms, driveshaft angle is pretty bad. It was leaking before i lifted it, and there's plenty of play in the pinion so not surprised. At least it looks the part :oops:

FORGE1 · Post by **FORGE1** » Mon Nov 28, 2011 11:23 am

Shot down to woodhill on Saturday but not for off roading, I had to pick up another bighorn off Roger so now I have a parts car which will be pulled apart over the next few weeks so I can do some work on my one. $150 in petrol for the round trip behind my petrol bighorn :oops:

He said it hadn't been started for over a year and I put a battery in and dropped some oil into it just to lube it up a bit and started first attempt with plenty of smoke but once that cleared I took it off the trailer and went for a drive (drives pretty well as well) but as its de-regd I will strip it down.

Also went to the Santa Parade in Aucks on Sunday arvo, daughter loved it so that was well worth it

mazdamike · Post by **mazdamike** » Tue Nov 29, 2011 6:21 pm

this is my uncles boat it uses about 9 lts a min flat out, super cool boat