SJ413 starter motor

redzuki · Post by **redzuki** » Tue Sep 26, 2006 10:32 pm

The starter motor in my sj413 is stuffed

and when i pulled it out it had a mitsubishi logo on it ,I was just woundering if there is another vehicle that has the same starter motor as a 413 that i could use as a replacement.

WACKO · Post by **WACKO** » Tue Sep 26, 2006 10:53 pm

pull it to bits and clean it out then replace the brushes in it. nice cheap n easyish.

Bubba · Post by **Bubba** » Thu Sep 28, 2006 9:14 am

Mitzi part, there's your problem.

Sorry WACKO, couldn't help taking a cheap shot :wink:

WACKO · Post by **WACKO** » Thu Sep 28, 2006 5:58 pm

dont worry. next time ill leave you in the bog. check if theres anything on your starter.... might be another problem part there....

red zuki... howd you get on? sussed?

redzuki · Post by **redzuki** » Thu Sep 28, 2006 7:13 pm

I was going to rebuild it but the housing the main shaft sits in is pretty worn out and i think theres a bearing on the shaft and thats rusted solid

.I've heard that holden barinas have the same engine as a 413 so i might go to pick a part tomorrow to see if theres a barina there to compare starters and see if there the same.
Jamie

Ben · Post by **Ben** » Thu Sep 28, 2006 8:29 pm

You can buy new bushes and brushes from Repco to rebuild it. Pretty easy job.

I'm pretty sure the Barinas/Swifts have the same starter, but with a different nose piece on it. Apparently you can swap the noses over, so pick a part could be a good option.

Ben

Jerry · Post by **Jerry** » Thu Sep 28, 2006 10:07 pm

Ahhh you made it home then.......I had horrible overheating (hopefully just mud on the radiator) It may not just be the bushes, my daihatsu one melted when it died.....I can ask around I know a couple of people with Zuks locally who may have spare parts

Otherwise just swop your motor for Mr Offroaders...I'm sure he won't notice or mind too much !!

redzuki · Post by **redzuki** » Thu Sep 28, 2006 10:18 pm

I ve had that 1.6 on my eye for a while

Jerry · Post by **Jerry** » Thu Sep 28, 2006 10:20 pm

Tell you what ...I'll distract him...Turoa will cut it out with his 9" grinder for you....no problem....

if he complains we'll just blame someone else and he'll be non the wiser :lol:

turoa · Post by **turoa** » Thu Sep 28, 2006 10:25 pm

well mroffroader has asked me to help with his SAS. So when hes not looking, ill "accidentally" chop out the ifs and the engine and "accidentally burn a 3.5 in there :lol:

Jerry · Post by **Jerry** » Thu Sep 28, 2006 10:27 pm

wouldn't it be easier to just swop the 413 badge with the Vitara badge? .....

Ryan · Post by **Ryan** » Fri Sep 29, 2006 6:36 am

redzuki wrote:The starter motor in my sj413 is stuffed and when i pulled it out it had a mitsubishi logo on it ,I was just woundering if there is another vehicle that has the same starter motor as a 413 that i could use as a replacement.

most trucks and cars have some sort of electrical bits made
by mitsubishi.... :?:

mroffroader · Post by **mroffroader** » Fri Sep 29, 2006 7:34 am

redzuki wrote:I ve had that 1.6 on my eye for a while

OI! get ur filthy eyes off my vitara! get ur own.....blardy! :evil:

none of this cutting my car to peices....not yet....untill one day when i have enough cash for the rover v8 and sas

....you can have my old thrashed worn out :roll:

motor then....i promise :lol:

redzuki · Post by **redzuki** » Fri Sep 29, 2006 4:49 pm

I went to pick apart and pulled a barina starter motor out and the front of the starter housing was different so i tried to change the front but it didn't work the main shafts where different sizes:( .
So i went to repco and got new bushes ,new brushes , a new bearing and a new gear that engages into the fly wheel for about fifty bucks,so now ive just got to go and fit it all .
Jamie

WACKO · Post by **WACKO** » Fri Sep 29, 2006 5:42 pm

redzuki wrote:I went to pick apart and pulled a barina starter motor out and the front of the starter housing was different so i tried to change the front but it didn't work the main shafts where different sizes:( .
So i went to repco and got new bushes ,new brushes , a new bearing and a new gear that engages into the fly wheel for about fifty bucks,so now ive just got to go and fit it all .
Jamie

good stuff. youll be zuking again in no time. :wink:

mroffroader · Post by **mroffroader** » Fri Sep 29, 2006 7:37 pm

WACKO wrote:
redzuki wrote:I went to pick apart and pulled a barina starter motor out and the front of the starter housing was different so i tried to change the front but it didn't work the main shafts where different sizes:( .
So i went to repco and got new bushes ,new brushes , a new bearing and a new gear that engages into the fly wheel for about fifty bucks,so now ive just got to go and fit it all .
Jamie

good stuff. youll be zuking again in no time.

:groupjump: yippie!

SJ413 starter motor

SJ413 starter motor

Re: SJ413 starter motor