What do these buttons do?

New to the site? Introduce yourself, tell us what 4wd(s) you have or your new to 4wding. Ask questions look for tips and hints in here.
Post Reply
User avatar
Militaris
Driver/Navigator
Posts: 27
Joined: Sun Feb 26, 2006 12:00 pm
Location: Blenheim

What do these buttons do?

Post by Militaris »

There are a couple of buttons/switches in my Toyota surf and I am not 100% sure what they do. I have my theories but after facts.


1) There is a switch which has 'hard/normal' written on it. When I switch this a little green 'Hard' appears on the display with a little picture of what I think looks like suspension.

I think this is suppose to make the suspension harder.... but not 100% sure. Was wonder what is the use of this switch and when should it be changed from normal to hard.

2) The other is a button down near the gear sticks. It has ECT power written on it. When clicked ECT power appears on the display. What is the point of this button and when should it be used?
nuts
Hard Yaka
Posts: 645
Joined: Wed Jul 19, 2006 12:00 pm
Location: somewhere arround westcoast offroading usually

buttons

Post by nuts »

1st button is hard for on road and soft for offroad .... dunno abt second button as drive a safari
people think i have a problem with insanity .... i dont i enjoy every minute ..... 0278900597
User avatar
rowinz
Hard Yaka
Posts: 119
Joined: Thu May 06, 2004 12:00 pm
Location: Rolleston

Post by rowinz »

Normal/hard alter shock absorber rate - hard gives harder ride. I use hard on road and normal offroad in my Prado.

ECT is the electronic transmission control. Power revs engine higher before changing gear. I don't use mine at all, but in other vehicles I use power when towing.
Rowan
KZJ78 LWB Prado
User avatar
Militaris
Driver/Navigator
Posts: 27
Joined: Sun Feb 26, 2006 12:00 pm
Location: Blenheim

Post by Militaris »

Thanks for the info.

I have been doing the opposite, using soft/normal on road and changing it to hard for off road.... well did a bit of testing and could not tell the difference when off road. Would keep it on soft for offroad use now.
Bubba
Hard Yaka
Posts: 1742
Joined: Mon Jul 05, 2004 12:00 pm
Location: Wellington

Post by Bubba »

I have had a play with the same soft/hard button on my fathers Surf, didn't notice any difference :?:
User avatar
fweddy
Hard Yaka
Posts: 1062
Joined: Fri Oct 13, 2006 12:00 pm
Location: North Canterbury

Post by fweddy »

While we are on surf buttons

On the right side of the steering wheel down low I have a switch that has an orange circle in it (guessing a lens) and the words "Deck Lamp".

When I switch it nothing happens.

In the back on the left hand side is a interior light which has a switch and doesn't work either. (Bulb is ok)

Do these relate to each other?

I figure perhaps the dash switch and orange lens are to let you know the rear interior light is going as it it too low to see from the front (due to the removable top).

Can any one help?
User avatar
Petemcc
Hard Yaka
Posts: 1405
Joined: Wed Sep 14, 2005 12:00 pm
Location: Queenstown

Post by Petemcc »

yea whats that deck lamp one. my old surf had one to and i neve figured it out...

pete
User avatar
Smurf
Hard Yaka
Posts: 2867
Joined: Tue Mar 04, 2003 12:00 pm
Location: Nelson

Post by Smurf »

pretty sure that you need the headlights on, then that decklamp switch works the light in the back, provided that the switch on the light is on also. but the switch in the back definitely needs to be on before the decklamp switch on the dash works
User avatar
SupraLux
Complete Bastard
Posts: 2415
Joined: Tue Dec 10, 2002 12:00 pm

Post by SupraLux »

The deck lamp switch is tied to the rear compartment side light... if the switch on the light itself is on, then you can use the deck lamp switch to turn it on and off... think it might also be tied into the rear door...

The hard soft switch is for the shock absorber valving... if you look at the shocks they should have a little round box thingy on top of them with some wires coming out (unless they have been replaced with aftermarket shocks). Generally they are useless after 100,000km or so and people replace them with aftermarket shocks and just ignore the switch.

The ECT POWER switch changes the point at which the auto will change gears (generally it increases by about 500RPM or so). Its just to allow the vehicle to rev out more before changing gear, thus having the revs higher when the new gear kicks in, making it easier to accelerate fast (in theory)

Steve
User avatar
fweddy
Hard Yaka
Posts: 1062
Joined: Fri Oct 13, 2006 12:00 pm
Location: North Canterbury

Post by fweddy »

Ahh - yup it works with the park lights

When park lights are on then either the rear or dash switch both work. (double switched - doesn't matter which way the back one is the front one just works opposite like two light switches in your house) problem is you can't have the rear light on when the lights are off so if you are getting in the back and want some light you have to run round to turn the parks on
User avatar
billyvanboheman
Hard Yaka
Posts: 513
Joined: Wed Aug 02, 2006 12:00 pm
Location: Christchurch

Post by billyvanboheman »

fweddy wrote: problem is you can't have the rear light on when the lights are off so if you are getting in the back and want some light you have to run round to turn the parks on


There must be a Japanese engineer somewhere who is still laughing his arse off at getting that system installed in a production vehicle
:!: :!: :lol:
1989 LWB Isuzu Bighorn, Intercooled 4JB1T, Ball Joint flip, Torsion bar wind, 3 inch stainless homebuilt snorkel,1/2 done electric fan mod,front sway bar quick disconnects, 15x8 ROH White Spokes,33x12.5x15 Hankooks.
User avatar
kiwilad
Newbie
Newbie
Posts: 2
Joined: Sun Oct 14, 2007 12:00 pm

Buttons also

Post by kiwilad »

I have a Nissan Terrano, it also has two switches Criuse/Sport. They don't seem to do anything either.
Post Reply

Return to “New Members and Beginners”