70 serries cv shaft

basics · Post by **basics** » Wed Nov 28, 2007 6:17 pm

i need to replace my L/H c.v shaft, will a 60 serries fit? or will i have to dog deeper for a 70 serries

Sadam_Husain · Post by **Sadam_Husain** » Wed Nov 28, 2007 6:20 pm

60 or 40 cv should fit your truck.

basics · Post by **basics** » Wed Nov 28, 2007 6:21 pm

im running a 40 stub axle so i dont see why not, thought i would check with you wize folk.

wopass · Post by **wopass** » Wed Nov 28, 2007 9:41 pm

yes will fit. 60's CV are slightly bigger than 40's and 70's slightly stronger again,then theres the 80's CV which is pretty big and strong..... but your best off just PMing SUZOLA and getting some....

:twisted:

LONGFIELDS :twisted:

thats if he has any left ?

wopass · Post by **wopass** » Wed Nov 28, 2007 9:42 pm

hang on.... or are you talking about the axle shaft ?

suzolla · Post by **suzolla** » Wed Nov 28, 2007 11:15 pm

Hi,
Are you talking about axle half shafts or CV's.
Have got some 27 spline Longfield CV's which should fit onto your standard axle half shafts or if you want super strong i have got a 40 series 30 spline super set which I am pretty sure will fit the 70 series as well, That is if Sadam (Marty) does not want it.

Haven't got a price yet as have not got freight and GST costs.

Thanks
Tim

basics · Post by **basics** » Thu Nov 29, 2007 6:36 pm

im talking about the shaft it self, not the cv.

jen took the 60 serries shaft to the mechanic this afternoon and he said it was too long. so wopass are you saying that the 60 will fit?

Sadam_Husain · Post by **Sadam_Husain** » Thu Nov 29, 2007 6:44 pm

The 40 series half shafts are the same as your 70#, I've already got 2 40# axles in my truck. I've got 2 spare ones here if you want one to get you going again, all you have to do is replace it :wink:

basics · Post by **basics** » Thu Nov 29, 2007 6:45 pm

your a ledgen. how much you after for it?

Sadam_Husain · Post by **Sadam_Husain** » Thu Nov 29, 2007 6:49 pm

basics wrote:your a ledgen. how much you after for it?

just come and grab it then find me a replacement one :wink:

basics · Post by **basics** » Thu Nov 29, 2007 6:50 pm

Sadam_Husain wrote:
basics wrote:your a ledgen. how much you after for it?

just come and grab it then find me a replacement one

done and done. flick me a pm with ya number or street address and ill pop down when ever your home

sig · Post by **sig** » Thu Nov 29, 2007 7:11 pm

i,ve got a stack of axles under the bench if you want one ,got three different lenghts so one is bound to be the one , if you still need one

sig · Post by **sig** » Thu Nov 29, 2007 7:13 pm

if you can give me a measurement i,ll go and have a look

oldblue · Post by **oldblue** » Thu Nov 29, 2007 7:17 pm

The 60s long axle[right side is about 40mm longer than a 70s right side axle]
The short axles an the same length.

sig · Post by **sig** » Thu Nov 29, 2007 7:22 pm

had a quick measure of the axles. and have a couple 740 long ,another couple 800 long,another couple 440 long and one 390 long hope this helps,most have got cvs attached as well

wopass · Post by **wopass** » Fri Nov 30, 2007 11:16 am

basics wrote:im talking about the shaft it self, not the cv.

jen took the 60 serries shaft to the mechanic this afternoon and he said it was too long. so wopass are you saying that the 60 will fit?

yea,nah yea...the CV would fit but the axle wont no, the 60 series axle is as you now know "to long" for the 70 :wink:

wopass · Post by **wopass** » Fri Nov 30, 2007 11:20 am

oldblue wrote:The 60s long axle[right side is about 40mm longer than a 70s right side axle]
The short axles an the same length.

nope.

pradoman · Post by **pradoman** » Fri Nov 30, 2007 11:59 am

what year is you 70 as were changed axles and cv's in 1990

Sadam_Husain · Post by **Sadam_Husain** » Fri Nov 30, 2007 1:05 pm

pradoman wrote:what year is you 70 as were changed axles and cv's in 1990

He picked up my spare 40# long axle and its the same length as the one he pulled out. That must make his truck a pre 1990.

I've got 2 40# axles in my truck now, a short front and a long rear so the pre 1990 70# must be the same axles as 40#

pradoman · Post by **pradoman** » Fri Nov 30, 2007 1:17 pm

hilux46/ 65/106 40 l/c's fine spline 60 and 70's pre 90 cv's are all the same.

wopass · Post by **wopass** » Fri Nov 30, 2007 1:20 pm

pradoman wrote:hilux46/ 65/106 40 l/c's fine spline 60 and 70's pre 90 cv's are all the same.

except for the main body O.D yes.

pradoman · Post by **pradoman** » Fri Nov 30, 2007 3:06 pm

no o/d still the same only changed in 1990 and only on the landcruiser

wopass · Post by **wopass** » Fri Nov 30, 2007 3:10 pm

pradoman wrote:no o/d still the same only changed in 1990 and only on the landcruiser

have you ever tried to fit a hilux or 60 or 70 series cv into a 40 series housing ?

basics · Post by **basics** » Fri Nov 30, 2007 5:30 pm

thanks for the offer sig, i got SH spare last night, now im juist waiting on the seal, will be here 1st thing tomorrow then i can go wheelin again.

:twisted:

only been with out my truck since tuesday, but feels alot longer :cry:

sig · Post by **sig** » Fri Nov 30, 2007 7:01 pm

no worries ,if any one else needs an axle and cv i,ve got lots and i,m changing to 80 series at some stage ,so they will all have to go eventually

Sadam_Husain · Post by **Sadam_Husain** » Fri Nov 30, 2007 7:09 pm

basics wrote: thanks for the offer sig, i got SH spare last night....blah blah blah...

Shit dont forget you've still got to replace my spare one :shock:

basics · Post by **basics** » Sat Dec 01, 2007 2:22 pm

Sadam_Husain wrote:
basics wrote: thanks for the offer sig, i got SH spare last night....blah blah blah...

Shit dont forget you've still got to replace my spare one

i remembered that last night after i had logged off, so sig. save me one and ill came and get it off ya :wink:

sig · Post by **sig** » Sat Dec 01, 2007 8:06 pm

no sweat ,got a few spares!!!!! :lol:

sig · Post by **sig** » Sat Dec 01, 2007 8:07 pm

just bring your old one or a measurement

BrentC · Post by **BrentC** » Mon Dec 10, 2007 1:51 pm

sig wrote:i,ve got a stack of axles under the bench if you want one ,got three different lenghts so one is bound to be the one , if you still need one

Hey Sig

Would have a 70 series front left axle - extended splines for factory front locker under that bench?

My man is moaning about Bus and Truck dicking him around and he wants his hoist back - has only been 2 weeks :shock:

Thanks
Brent

70 serries cv shaft

70 serries cv shaft

cv

Re: cv

cv

Re: cv

cv

Re: cv