Page 1 of 1
WTD Urgently Samurai / SJ413 driveshaft
Posted: Mon May 21, 2012 3:05 pm
by zukmeista
Blew a uni and it damaged the ears on the yoke so I need another driveshaft ASAP. Any help would be appreciated.
Re: WTD Urgently Samurai driveshaft
Posted: Mon May 21, 2012 3:44 pm
by DieselBoy
What end of the drive shaft????
May have something that might work. I have a drive shaft with a busted rear yoke after a spring breakage, but a good front yoke.
If its the front joint of the rear shaft that's crapped out on yours, you may be able to just pull it apart at the slip joint and plug the good end of this one into it??
Re: WTD Urgently Samurai driveshaft
Posted: Mon May 21, 2012 5:31 pm
by zukmeista
DieselBoy wrote:What end of the drive shaft????
May have something that might work. I have a drive shaft with a busted rear yoke after a spring breakage, but a good front yoke.
If its the front joint of the rear shaft that's crapped out on yours, you may be able to just pull it apart at the slip joint and plug the good end of this one into it??
Sounds farken good to me
Tis the female bit, must be off a samurai tho as they have 10mm holes as opposed to a 413's 8mm.
Re: WTD Urgently Samurai driveshaft
Posted: Tue May 22, 2012 5:02 pm
by zukmeista
Anyone? Can't really afford Mudbits pricing
Re: WTD Urgently Samurai driveshaft
Posted: Tue May 22, 2012 5:48 pm
by Rotazuk
Do you mean the bit that bolts to the diff ? if so you will have to find one . if its any other part you should be able to fit a 413 part . 413 , samurai and vitara all run the same size uj so you should be able to mix and match .
Re: WTD Urgently Samurai driveshaft
Posted: Tue May 22, 2012 8:53 pm
by DieselBoy
Can the holes just be drilled out to 10mm? The shaft I have is a 413.
Re: WTD Urgently Samurai driveshaft
Posted: Wed May 23, 2012 8:21 am
by zukmeista
Rotazuk wrote:Do you mean the bit that bolts to the diff ? if so you will have to find one . if its any other part you should be able to fit a 413 part . 413 , samurai and vitara all run the same size uj so you should be able to mix and match .
Thanks, I need the female end, the bit that bolts to the transfer is fine but the other side isn't. Seeing as 413's have a transfer mounted handbrake will it be shorter?
Re: WTD Urgently Samurai driveshaft
Posted: Thu May 24, 2012 7:04 am
by Rotazuk
No , from memory the t/case without the brake has a flange that takes up the same space as the drum brake drum that the shaft mounts to .
All my stuff is in storage so ask someone to measure each one . I think they are the same length thou . I would be looking for a 413 shaft end and swapping your diff flange over if its still good .
Chris
Re: WTD Urgently Samurai driveshaft
Posted: Thu May 24, 2012 8:36 am
by zukmeista
Thanks for your help. And seeing as a picture is worth a thousand words
this is what I need:
Re: WTD Urgently Samurai driveshaft
Posted: Thu May 24, 2012 10:36 am
by Rotazuk
That should be the same no matter what the length , you could get one off a front or rear shaft . Think I biffed all mine but will have a look when I go to the storage this arvo .
Chris
Re: WTD Urgently Samurai driveshaft
Posted: Tue May 29, 2012 3:46 pm
by zukmeista
I'm waiting !:mrgreen:
Re: WTD Urgently Samurai / SJ413 driveshaft
Posted: Sat Jun 09, 2012 5:28 pm
by zukmeista
Someone must have something? really need this cause I can't go 4wding till I have one
