Page 1 of 1
SJ413 starter motor
Posted: Tue Sep 26, 2006 10:32 pm
by redzuki
The starter motor in my sj413 is stuffed
and when i pulled it out it had a mitsubishi logo on it ,I was just woundering if there is another vehicle that has the same starter motor as a 413 that i could use as a replacement.
Posted: Tue Sep 26, 2006 10:53 pm
by WACKO
pull it to bits and clean it out then replace the brushes in it. nice cheap n easyish.
Posted: Thu Sep 28, 2006 9:14 am
by Bubba
Mitzi part, there's your problem.
Sorry WACKO, couldn't help taking a cheap shot
Posted: Thu Sep 28, 2006 5:58 pm
by WACKO
dont worry. next time ill leave you in the bog. check if theres anything on your starter.... might be another problem part there....
red zuki... howd you get on? sussed?
Posted: Thu Sep 28, 2006 7:13 pm
by redzuki
I was going to rebuild it but the housing the main shaft sits in is pretty worn out and i think theres a bearing on the shaft and thats rusted solid
.I've heard that holden barinas have the same engine as a 413 so i might go to pick a part tomorrow to see if theres a barina there to compare starters and see if there the same.
Jamie
Posted: Thu Sep 28, 2006 8:29 pm
by Ben
You can buy new bushes and brushes from Repco to rebuild it. Pretty easy job.
I'm pretty sure the Barinas/Swifts have the same starter, but with a different nose piece on it. Apparently you can swap the noses over, so pick a part could be a good option.
Ben
Posted: Thu Sep 28, 2006 10:07 pm
by Jerry
Ahhh you made it home then.......I had horrible overheating (hopefully just mud on the radiator) It may not just be the bushes, my daihatsu one melted when it died.....I can ask around I know a couple of people with Zuks locally who may have spare parts
Otherwise just swop your motor for Mr Offroaders...I'm sure he won't notice or mind too much !!
Posted: Thu Sep 28, 2006 10:18 pm
by redzuki
I ve had that 1.6 on my eye for a while
Posted: Thu Sep 28, 2006 10:20 pm
by Jerry
Tell you what ...I'll distract him...Turoa will cut it out with his 9" grinder for you....no problem....
if he complains we'll just blame someone else and he'll be non the wiser
Posted: Thu Sep 28, 2006 10:25 pm
by turoa
well mroffroader has asked me to help with his SAS. So when hes not looking, ill "accidentally" chop out the ifs and the engine and "accidentally burn a 3.5 in there
Posted: Thu Sep 28, 2006 10:27 pm
by Jerry
wouldn't it be easier to just swop the 413 badge with the Vitara badge? .....
Re: SJ413 starter motor
Posted: Fri Sep 29, 2006 6:36 am
by Ryan
redzuki wrote:The starter motor in my sj413 is stuffed
and when i pulled it out it had a mitsubishi logo on it ,I was just woundering if there is another vehicle that has the same starter motor as a 413 that i could use as a replacement.
most trucks and cars have some sort of electrical bits made
by mitsubishi....
Posted: Fri Sep 29, 2006 7:34 am
by mroffroader
redzuki wrote:I ve had that 1.6 on my eye for a while
OI! get ur filthy eyes off my vitara! get ur own.....blardy!
none of this cutting my car to peices....not yet....untill one day when i have enough cash for the rover v8 and sas
....you can have my old thrashed worn out
motor then....i promise
Posted: Fri Sep 29, 2006 4:49 pm
by redzuki
I went to pick apart and pulled a barina starter motor out and the front of the starter housing was different so i tried to change the front but it didn't work the main shafts where different sizes:( .
So i went to repco and got new bushes ,new brushes , a new bearing and a new gear that engages into the fly wheel for about fifty bucks,so now ive just got to go and fit it all .
Jamie
Posted: Fri Sep 29, 2006 5:42 pm
by WACKO
redzuki wrote:I went to pick apart and pulled a barina starter motor out and the front of the starter housing was different so i tried to change the front but it didn't work the main shafts where different sizes:( .
So i went to repco and got new bushes ,new brushes , a new bearing and a new gear that engages into the fly wheel for about fifty bucks,so now ive just got to go and fit it all .
Jamie
good stuff. youll be zuking again in no time.
Posted: Fri Sep 29, 2006 7:37 pm
by mroffroader
WACKO wrote:redzuki wrote:I went to pick apart and pulled a barina starter motor out and the front of the starter housing was different so i tried to change the front but it didn't work the main shafts where different sizes:( .
So i went to repco and got new bushes ,new brushes , a new bearing and a new gear that engages into the fly wheel for about fifty bucks,so now ive just got to go and fit it all .
Jamie
good stuff. youll be zuking again in no time.
:groupjump: yippie!