Offroad-Express

i need to replace my L/H c.v shaft, will a 60 serries fit? or will i have to dog deeper for a 70 serries

60 or 40 cv should fit your truck.

im running a 40 stub axle so i dont see why not, thought i would check with you wize folk.

yes will fit. 60's CV are slightly bigger than 40's and 70's slightly stronger again,then theres the 80's CV which is pretty big and strong..... but your best off just PMing SUZOLA and getting some....

LONGFIELDS

thats if he has any left ?

hang on.... or are you talking about the axle shaft ?

Hi,
Are you talking about axle half shafts or CV's.
Have got some 27 spline Longfield CV's which should fit onto your standard axle half shafts or if you want super strong i have got a 40 series 30 spline super set which I am pretty sure will fit the 70 series as well, That is if Sadam (Marty) does not want it.

Haven't got a price yet as have not got freight and GST costs.

Thanks
Tim

im talking about the shaft it self, not the cv.

jen took the 60 serries shaft to the mechanic this afternoon and he said it was too long. so wopass are you saying that the 60 will fit?

The 40 series half shafts are the same as your 70#, I've already got 2 40# axles in my truck. I've got 2 spare ones here if you want one to get you going again, all you have to do is replace it

your a ledgen. how much you after for it?

basics wrote:your a ledgen. how much you after for it?

just come and grab it then find me a replacement one

Sadam_Husain wrote:

basics wrote:your a ledgen. how much you after for it?

just come and grab it then find me a replacement one

done and done. flick me a pm with ya number or street address and ill pop down when ever your home

i,ve got a stack of axles under the bench if you want one ,got three different lenghts so one is bound to be the one , if you still need one

if you can give me a measurement i,ll go and have a look

The 60s long axle[right side is about 40mm longer than a 70s right side axle]
The short axles an the same length.

had a quick measure of the axles. and have a couple 740 long ,another couple 800 long,another couple 440 long and one 390 long hope this helps,most have got cvs attached as well

basics wrote:im talking about the shaft it self, not the cv.

jen took the 60 serries shaft to the mechanic this afternoon and he said it was too long. so wopass are you saying that the 60 will fit?

yea,nah yea...the CV would fit but the axle wont no, the 60 series axle is as you now know "to long" for the 70

oldblue wrote:The 60s long axle[right side is about 40mm longer than a 70s right side axle]
The short axles an the same length.

nope.

what year is you 70 as were changed axles and cv's in 1990

pradoman wrote:what year is you 70 as were changed axles and cv's in 1990

He picked up my spare 40# long axle and its the same length as the one he pulled out. That must make his truck a pre 1990.

I've got 2 40# axles in my truck now, a short front and a long rear so the pre 1990 70# must be the same axles as 40#

hilux46/ 65/106 40 l/c's fine spline 60 and 70's pre 90 cv's are all the same.

pradoman wrote:hilux46/ 65/106 40 l/c's fine spline 60 and 70's pre 90 cv's are all the same.

except for the main body O.D yes.

no o/d still the same only changed in 1990 and only on the landcruiser

pradoman wrote:no o/d still the same only changed in 1990 and only on the landcruiser

have you ever tried to fit a hilux or 60 or 70 series cv into a 40 series housing ?

thanks for the offer sig, i got SH spare last night, now im juist waiting on the seal, will be here 1st thing tomorrow then i can go wheelin again.




only been with out my truck since tuesday, but feels alot longer

no worries ,if any one else needs an axle and cv i,ve got lots and i,m changing to 80 series at some stage ,so they will all have to go eventually

basics wrote: thanks for the offer sig, i got SH spare last night....blah blah blah...

Shit dont forget you've still got to replace my spare one

Sadam_Husain wrote:

basics wrote: thanks for the offer sig, i got SH spare last night....blah blah blah...

Shit dont forget you've still got to replace my spare one

i remembered that last night after i had logged off, so sig. save me one and ill came and get it off ya

no sweat ,got a few spares!!!!!

just bring your old one or a measurement

sig wrote:i,ve got a stack of axles under the bench if you want one ,got three different lenghts so one is bound to be the one , if you still need one

Hey Sig

Would have a 70 series front left axle - extended splines for factory front locker under that bench?

My man is moaning about Bus and Truck dicking him around and he wants his hoist back - has only been 2 weeks

Thanks
Brent