cone washers

[new2zukes]

hi i think they are cone washers but what i need is on a asin manual hub it centers the bolt then the spring washer goes over that then the bolt, are these cone washers? if so where can i get some of them from, i tryed ripco but they just looked at me funny. hope someone can help me.


martin

[mudmike]

I got mine from toyota, not to bad a price, I tryed to find them at a few fastner places and they said go to toyota. Maybe someone will know of a place but have not found them yet. good luck

[new2zukes]

ok thanks for that il go to toyota dealer on monday to see what they say thanks..
martin

[flyingbrick]

i tryed ripco but they just looked at me funny.

I've never made a parts request at repco without getting that look.

[Taz]

I got mine from toyota, not to bad a price, I tryed to find them at a few fastner places and they said go to toyota. Maybe someone will know of a place but have not found them yet. good luck

Did you try blacks? Have never said no to anything I've asked for.

[mudzilla]

NZ Bus and Truck ph 092636021

[fweddy]

The local Toyota outfit were going to charge me about $10 a cone washer, My contact at Pacific Toyota (Tauranga) was about $8.30 a cone. I got the full stud, cone, spring washer, nut from Just Cruisers for $7+Gst.

How many do you need?

[Sadam_Husain]

The local Toyota outfit were going to charge me about $10 a cone washer

I cant understand these Toyota outfits and their prices, $60 per hub for the cone washers and I've just receicved a draglink, tierod and 4 ball joints from japan (poss airfreighted coz it only took 2 weeks) for $80 plus gst....and the joker told me that was their standard retail price...go figure?

[Heath]

Suzuki parts world in Te puke or was it mudbits in tauranga (cant remember) had some $1 a piece when I bought my 3 free wheeling hubs for the vitara. Apparently they are all just about interchangeable so they may be the right size.

Heath

[new2zukes]

Suzuki parts world in Te puke or was it mudbits in tauranga (cant remember) had some $1 a piece when I bought my 3 free wheeling hubs for the vitara. Apparently they are all just about interchangeable so they may be the right size.

Heath

1$ sounds like a better price, bound to have gone up by now though.

The local Toyota outfit were going to charge me about $10 a cone washer

I cant understand these Toyota outfits and their prices, $60 per hub for the cone washers and I've just receicved a draglink, tierod and 4 ball joints from japan (poss airfreighted coz it only took 2 weeks) for $80 plus gst....and the joker told me that was their standard retail price...go figure?

i cant understand toyoto places either with their prices just because they are called toyota doesnt mean they have to charge the world.

The local Toyota outfit were going to charge me about $10 a cone washer, My contact at Pacific Toyota (Tauranga) was about $8.30 a cone. I got the full stud, cone, spring washer, nut from Just Cruisers for $7+Gst.

How many do you need?

i need 7 cone washers

cheers

martin

[SupraLux]

Repco have them, they just don't know it... In fairness to them, its not a very common item and if you hadn't pulled 4WD hubs apart before you'd probably not know what they were...

P/N 041021096
Stud Kit - Axle Flange

Contains one stud, one cone washer, one lock washer, one nut.

Cost - should be around the same price Fweddy mentioned.

Steve

[new2zukes]

ok thanks heeps for that il give it a go.

martin

[j_tomo]

ive got some on my old parts surf, do you want them?

[nstacey]

Repco have them

P/N 041021096
Stud Kit - Axle Flange

Contains one stud, one cone washer, one lock washer, one nut.

FYI I can confirm Repco still have this part in their system, they had to order them in but they were only $2.40 a piece. Picked some up this afternoon