Page 1 of 1

Hi~ ALL New member here!!

Posted: Thu May 05, 2011 6:05 pm
by tristan
Hi~ My online name is Tristan..
I live in albany North shore AKL

I got a JEEP TJ Wrangler.
Image
- 31 AT Goodyear Tyre
- Old man emu 2.5" inch up
- Safari Snorkel

and some curious
I got a brand new burket seats but I heard that It's need register
I don't know how to that??

And I really need TJ Soft top + hard ware I got an only harf top. TT.

Please let me know~~ Brothers~~

Cheers~

[Tristan]

Re: Hi~ ALL New member here!!

Posted: Thu May 05, 2011 6:33 pm
by suzookyman
If seats are on the original seat bases they don't need cert (same mount holes etc )
Al

Re: Hi~ ALL New member here!!

Posted: Thu May 05, 2011 7:39 pm
by sibainmud
Welcome Tristan,
I have seen that jeep around Albany.
As Suzookyman says, if the seats are a straight fit then no cert is needed.
A full hard top shouldn't be too hard to find.
Save a search on Trade Me and see what comes up.
Are you in a 4x4 club?
It is a good way of getting to know the places to go off-roading and can be a source of good deals on parts and spares.

Cheers,
Simon Collett
President,
Norwest OHV Club Inc.

Re: Hi~ ALL New member here!!

Posted: Thu May 05, 2011 11:24 pm
by tristan
Thanks guys~
Nice me to sibainmud

My new seat is burket type, and then it doesn't fit original hole..
And I'm looking for soft top and hard frame(not hardtop)

I want to meet some good offroad friend on offline ^^

C U the Offroad
[Tristan]

Re: Hi~ ALL New member here!!

Posted: Fri May 06, 2011 1:42 pm
by tristan
I'm from Korea.. :D

Re: Hi~ ALL New member here!!

Posted: Fri May 06, 2011 9:44 pm
by Hilux Dan
Hi Tristan,

So do the bucket seats have there own running tracks to slide backwards and forwards on ??

If not, then can you fit the bucket seats to the old running tracks which will obviously fit into the factory holes ??

Have you been out to Woodhill forest for a play yet ??

Cheers

Dan

Re: Hi~ ALL New member here!!

Posted: Fri May 06, 2011 11:42 pm
by Drurban
Hi Tristan,

Nice truck you got there, you should get a decent set of mud tyres for your truck, you will find that you will go through place that you cannot with the AT's.

You should try Woodhill, that would be a great place for your truck.

Cheers

Ruben

Re: Hi~ ALL New member here!!

Posted: Sun May 08, 2011 10:08 am
by tristan
Dan/
Hi mate~
New bucket seats too wide then original seats.
I think need a special bracket ^^

http://cfile2.uf.tistory.com/image/1603934E4DB618C6057022



and I naver been to Woodhill but I really want to go there~

Cheers

[Tristan]

Re: Hi~ ALL New member here!!

Posted: Sun May 08, 2011 10:23 am
by SP450andLE
Tristan,
You can upload the photo to photobucket.com, resize it to 640x480, and then just put the link to the photo between the two img tags - [img]here[/img]
(They are near the top when you are writing a post :wink: :D)

That way you can put the photo directly into your post :mrgreen:

Re: Hi~ ALL New member here!!

Posted: Sun May 08, 2011 10:28 am
by Overkill
tristan wrote:Dan/
New bucket seats too wide then original seats.
I think need a special bracket ^^

http://cfile2.uf.tistory.com/image/1603934E4DB618C6057022
Pop down to your local engineering shop and get a couple of 5-6mm plate strips. You can mount your new seats to the strip and the strip to mounting rails in the correct location.

I have done this to my Discovery and it has come out mint, will get into the garage and take a pic........just incase what I wrote didn't make any sense :mrgreen:

Re: Hi~ ALL New member here!!

Posted: Sun May 08, 2011 3:11 pm
by tristan
Ruben/
Thanks~ for the replay..
I agree with u~ next time I'll consider ur opinion ^^


SP450andLE/
Thanks~ ur infom
I'll do that next time~


Overkill/
Thanks~ ur replay
how about cert??
I went 4wd shop someone said U should get a cert!
want to see the pic~


Cheers

[Tristan]

Re: Hi~ ALL New member here!!

Posted: Sun May 08, 2011 6:52 pm
by Overkill
Hi Tristan

When I replaced my OE seats in an old Pajero I had with some new bucket seats, I went in to get a cert for a few mods I had done. The certifier said that as long as I used the original seat rails I did not need to get them certified, but he did them for me so it made the whole lot of mods I did legal. If you change the rails for ones that will fit, you WILL need to get the cert asap.

Here's some of the pics that I have done to my Disco, I had given it a WOF through VTNZ and it passed no problems with the seats the way they are.

Excuse the dirt, the camera adds 10 pounds of dirt for sure :lol: :lol: Doesn't look this dirty in the day time.....damn flash :mrgreen:


Image
Image
Image
Image
Image

Re: Hi~ ALL New member here!!

Posted: Sun May 08, 2011 8:58 pm
by Mattman
My experience with seats and belts is that you only need to get belt mounts certed.

My soarer seats had the buckles mounted to them so I had to get new belt mounts certed installed on the tunnel. No issues with seat frames at all.

Matt.

Re: Hi~ ALL New member here!!

Posted: Thu May 19, 2011 5:24 pm
by tristan
Overkill/
Thanks for the photos~
and I really sorry about late replay.
anyway I just refer to the your opinion and photos~~
Thanks~~!


Mattman/
Thanks for your reply
that a good new for me~~ :D


Cheers

[Tristan]