PTO Winch WANTED

Beer_Cruiser · Post by **Beer_Cruiser** » Mon Jul 30, 2007 8:46 pm

WANTED PTO WINCH for 70 series Toyota
Have seen a 60 series on TM. Would it fit?
Whats the deal with the gears?

skid · Post by **skid** » Mon Jul 30, 2007 9:12 pm

Beer_Cruiser wrote:WANTED PTO WINCH for 70 series Toyota
Have seen a 60 series on TM. Would it fit?
Whats the deal with the gears?

look back thru other posts about winches or PM Wopass, hes the toyota PTO winch expert

Sadam_Husain · Post by **Sadam_Husain** » Mon Jul 30, 2007 10:06 pm

Got a complete one but I'm not letting go of it. You'll have to make sure that you get the right PTO for your split transfercase and you'll have to check that you have the drive gear in your transfercase, some do and some just have a spacer on the shaft where the drive gear goes.

Might need to have a look at where your exhaust runs if its on the passenger side of the truck :wink:

monstr · Post by **monstr** » Mon Jul 30, 2007 10:27 pm

Hi Check out trade me auct no 111433736 A complete pto for a 70 ...Cheers

Beer_Cruiser · Post by **Beer_Cruiser** » Mon Jul 30, 2007 10:32 pm

if i take square cover off transfercase will i be able to see if ive got drive gear? wot am i looking for.
is it hard to get drive gear in t/c? i have enuff knowledge to be dangerous

Sadam_Husain · Post by **Sadam_Husain** » Mon Jul 30, 2007 10:49 pm

if you take the PTO blanking plate off you'll be looking at the output shaft, the PTO drive gear is a square cut gear towards the rear of the shaft, if its not there the shaft will just have a spacer like a tube in its place to hold the other helical gears in place. My 70# dosent have one but I've got a spare 40# transfer case that has one in it.

It's not a major to split the transfercase to put the drive gear in :drunken:

Beer_Cruiser · Post by **Beer_Cruiser** » Tue Jul 31, 2007 6:08 am

thanks for your help. will have a look tonight after work

Sadam_Husain · Post by **Sadam_Husain** » Tue Jul 31, 2007 8:47 am

the picture stolen from some internet site shows the PTO drive gear on the end of the shaft, its not easy to see through the side of the t/c still in the truck but you should be able to work out if its there or not :shock:

Beer_Cruiser · Post by **Beer_Cruiser** » Tue Jul 31, 2007 8:18 pm

had a look tonight can see what looks like pto drive gears on the shaft at the rear end of the t/c between these gears and next lot of gears theres small spacer maybe 50mm. these gears are intermeshing while the gears at the back of the t/c (pto drive gears?) do not seem to meet.

sorry about the flash terminology this is all pretty new to me.thanks for the pic i think thats what i was looking at. didnt have camera or would have taken pic.

Beer_Cruiser · Post by **Beer_Cruiser** » Wed Aug 01, 2007 12:02 pm

does enyone know if a 60series pto winch will fit my 70.there seems to be a shit load of them around

sig · Post by **sig** » Wed Aug 01, 2007 1:39 pm

the winchs are the same but the mounting brackets are different and the driveshaft lenght will be different as well

Beer_Cruiser · Post by **Beer_Cruiser** » Wed Aug 01, 2007 4:18 pm

thanks for help will keep that in mind

PTO Winch WANTED

PTO Winch WANTED

Re: PTO Winch WANTED