Newbee

For all Mitsubisih related topics

User avatar
mytronic
Hard Yaka
Posts: 170
Joined: Tue Aug 22, 2006 12:00 pm
Location: Gisborne
Contact:

Newbee

Post by mytronic »

Hi all

Thinking of getting a 1993 Pajero 3dr Softtop all kitted out.
Is there anything that I should be aware of?
The last three Mitsubishi's that attended one of our club runs broke CV's, is this a common fault?
This one has Factory Electric Diff Locker, any good?
230,000km with new Cambelt,shocks and Clutch.
Replacing my Jeep Cherokee that got very expensive to keep running.
Look forward to all comments

Cheers Mike :roll:
User avatar
NJV6
Hard Yaka
Posts: 2751
Joined: Mon Nov 15, 2004 12:00 pm
Location: Southland

Post by NJV6 »

3 cv's :shock:


Thats pretty nasty, they are a strong unit, possibly the strongest of the IFS front ends according to outerlimits guys. It is not a common fault to break cv's. Factory lockers are stonger than axles - JTop will know about that, they are a strong unit but I also know they do need the full pressure to work them (they are a factory air locker) as I shore all the teeth off mine.

they are basically a pretty substantial unit.
SWB V6 Paj with one or two mods ;)
User avatar
WACKO
Pyro
Posts: 990
Joined: Sat Feb 11, 2006 12:00 pm
Location: Lower Hutt

Post by WACKO »

im sure they are great trucks when you look after them... :oops: but the diesels have problems(so i hear). i have a 93 jtop 3ltr v6. i am VERY pleased with it, in the two years i have owned it i have replaced a wheel bearing, 1 inner cv and the transfur box and rebuilt the starter.
the transfur could have been avoided with better maintenince. but all that aside, it gets thrashed and keeps coming back for more. :D
not sure bout the reliability of the lockers as i havnt put mine in yet, but they cant be all bad, not as good as an ARB but still alright id say.
User avatar
mytronic
Hard Yaka
Posts: 170
Joined: Tue Aug 22, 2006 12:00 pm
Location: Gisborne
Contact:

Post by mytronic »

Thanks for that , we mainly have Zukes in our club and I want something a little different, with power to boot. Bought a Korando ,goes well but loath to get into the flesh of the club run. My old Jeep Cherokee would run circles around it. On that note are the 3l Mits thursty?
The mits I'm looking at is fairly dented and well used as a club truck.
No lift Kit, but has new starter Motor, shocks, springs and CV's !! 4 point roll cage, new cam
I agree that it was unusual for 3 CV's to bust ,hence my question. Also everytime I mention the M word I get shot down by mechanics. But thus far reports have been good. Just a little confused on the matter.
User avatar
mytronic
Hard Yaka
Posts: 170
Joined: Tue Aug 22, 2006 12:00 pm
Location: Gisborne
Contact:

Post by mytronic »

WACKO wrote:im sure they are great trucks when you look after them... :oops: but the diesels have problems(so i hear). i have a 93 jtop 3ltr v6. i am VERY pleased with it, in the two years i have owned it i have replaced a wheel bearing, 1 inner cv and the transfur box and rebuilt the starter.
the transfur could have been avoided with better maintenince. but all that aside, it gets thrashed and keeps coming back for more. :D
not sure bout the reliability of the lockers as i havnt put mine in yet, but they cant be all bad, not as good as an ARB but still alright id say.


This truck is in your neibourhood I believe. Levin club. Do you know of it from the description, Bright red ? Just a shot in the dark !!
User avatar
WACKO
Pyro
Posts: 990
Joined: Sat Feb 11, 2006 12:00 pm
Location: Lower Hutt

Post by WACKO »

tonys?... red with silver flares? i got a windscreen off him :lol: it seems to go quite well. the 3ltrs are very thursy, but the 3.5s are worse i think... :lol:
User avatar
JTop
Hard Yaka
Posts: 236
Joined: Mon Jan 09, 2006 12:00 pm

Post by JTop »

The 3 litres are hungry but no worse than a Heep.
You will probably find the shorter wheel base a little unnerving till you get used to it on hillsIt would be my pick of the mid sized trucks
J Top
User avatar
NJV6
Hard Yaka
Posts: 2751
Joined: Mon Nov 15, 2004 12:00 pm
Location: Southland

Post by NJV6 »

I don't think the 3.5's are any worse petrol wise. They don't need to work very hard to do anything thats for sure. I have a 3.5 5 speed shorty and am rapt with it.

Early mitsi diesels were a little problematic and the 3.0's can do head gaskets (padero on here had one) but I'm not sure why they did them.
SWB V6 Paj with one or two mods ;)
User avatar
mytronic
Hard Yaka
Posts: 170
Joined: Tue Aug 22, 2006 12:00 pm
Location: Gisborne
Contact:

Post by mytronic »

WACKO wrote:tonys?... red with silver flares? i got a windscreen off him :lol: it seems to go quite well. the 3ltrs are very thursy, but the 3.5s are worse i think... :lol:


Thats the one !
:P
User avatar
WACKO
Pyro
Posts: 990
Joined: Sat Feb 11, 2006 12:00 pm
Location: Lower Hutt

Post by WACKO »

haha.. why is he selling it?
User avatar
mytronic
Hard Yaka
Posts: 170
Joined: Tue Aug 22, 2006 12:00 pm
Location: Gisborne
Contact:

Post by mytronic »

Thanks for the input. Feel alot better about the Mits now.
Not too sure why he is selling yet, think he want's a tuff truck again?
Was a bit busy when I was talking to him this afternoon. Don't think it is a secret as it is listed
User avatar
Smurf
Hard Yaka
Posts: 2867
Joined: Tue Mar 04, 2003 12:00 pm
Location: Nelson

Post by Smurf »

Have 2 mates in SWB 3.5 V6 pajeros, heaps more grunt than the 3.0 V6 but both 3.5s burn oil and have very noisy(rattly) motors, both around 130 000 kms. The 3.5s are a lot thirstier than the 3.0 One mate had a 3 litre before going to a 3.5, He wishes he stll had the 3.0, easier to work on motor, cheaper to run.
User avatar
WACKO
Pyro
Posts: 990
Joined: Sat Feb 11, 2006 12:00 pm
Location: Lower Hutt

Post by WACKO »

yeah ive seen it on trade me... :lol: get jtop to sas it and it will be unstopable... :lol:
User avatar
NJV6
Hard Yaka
Posts: 2751
Joined: Mon Nov 15, 2004 12:00 pm
Location: Southland

Post by NJV6 »

Smurf wrote:Have 2 mates in SWB 3.5 V6 pajeros, heaps more grunt than the 3.0 V6 but both 3.5s burn oil and have very noisy(rattly) motors, both around 130 000 kms.


SSSHHHHHHHH I can't hear you.... Mine has 98000 and is still quiet, very quiet in fact. burble out the exhaust and injectors clicking quiet. Does need prob 2 litres of oil every 10000k which I don't worry about - it puffs out when on overrun down bloody steep hills. (only did 5200km last year)
SWB V6 Paj with one or two mods ;)
User avatar
mytronic
Hard Yaka
Posts: 170
Joined: Tue Aug 22, 2006 12:00 pm
Location: Gisborne
Contact:

Post by mytronic »

Oh, here we go.
Rattly ?
I am a VERY hard driver and expect my vehicle to go where I point it. Without watching the Rev counter etc. We have very deep sticky clay mud here in Gisborne.
The Cherokee only just kept up. Well engine wise anyhow.
Rest of it kept falling apart. That is why I sold it, I'm no mechanic. Fix a computer or a TV, that I can do. Fix a vehicle, that is another story. 8)
Last edited by mytronic on Tue Aug 22, 2006 10:52 pm, edited 1 time in total.
User avatar
mytronic
Hard Yaka
Posts: 170
Joined: Tue Aug 22, 2006 12:00 pm
Location: Gisborne
Contact:

Post by mytronic »

WACKO wrote:yeah ive seen it on trade me... :lol: get jtop to sas it and it will be unstopable... :lol:


Sorry SAS it ?
User avatar
NJV6
Hard Yaka
Posts: 2751
Joined: Mon Nov 15, 2004 12:00 pm
Location: Southland

Post by NJV6 »

Called a rev limiter.... :idea: :roll: 8)
SWB V6 Paj with one or two mods ;)
User avatar
WACKO
Pyro
Posts: 990
Joined: Sat Feb 11, 2006 12:00 pm
Location: Lower Hutt

Post by WACKO »

mine is a little rattly from a underwater excursion... one day i will sort the front pulleys out... but not the tappets or anything and its done 180somthing odd kms. it uses oil but think thats the seals around the back of the tappet covers, its oily round there. but i only use it for 4wdn so im not too worried.
User avatar
mytronic
Hard Yaka
Posts: 170
Joined: Tue Aug 22, 2006 12:00 pm
Location: Gisborne
Contact:

Post by mytronic »

NJV6 wrote:Called a rev limiter.... :idea: :roll: 8)


Yep, heard of those :!:
Great devices, never used one, perhaps I should aye :?:
Life is all fun when playin in the Mud

Unstoppable is what I need. Sick of Duds :wink:
User avatar
mytronic
Hard Yaka
Posts: 170
Joined: Tue Aug 22, 2006 12:00 pm
Location: Gisborne
Contact:

Post by mytronic »

Question.
Why does the wording under my name change ? :shock:
User avatar
WACKO
Pyro
Posts: 990
Joined: Sat Feb 11, 2006 12:00 pm
Location: Lower Hutt

Post by WACKO »

SAS.. Solid Axle Swap :D. the wording, do you mean winch master? the only thing i can work out is that as you make more posts you get a differant um... "status"
Last edited by WACKO on Tue Aug 22, 2006 11:04 pm, edited 1 time in total.
User avatar
mytronic
Hard Yaka
Posts: 170
Joined: Tue Aug 22, 2006 12:00 pm
Location: Gisborne
Contact:

Post by mytronic »

Yeah

First it was Stropper, now winch master , what's up with that?
Suspect system generated because I'm not a paid member ?
User avatar
WACKO
Pyro
Posts: 990
Joined: Sat Feb 11, 2006 12:00 pm
Location: Lower Hutt

Post by WACKO »

nah. im not 100% sure if it means anything really, besides lots of posts...
User avatar
mytronic
Hard Yaka
Posts: 170
Joined: Tue Aug 22, 2006 12:00 pm
Location: Gisborne
Contact:

Post by mytronic »

Well, thanks to all for the chat. Way past by beauty sleep (not that it ever works) :!: :!:

Will be back when I contact Tony later this week.
SAS, aha !! later, much later.

Most appreciated
Surprised no coments about my Ssangyong :roll:
User avatar
WACKO
Pyro
Posts: 990
Joined: Sat Feb 11, 2006 12:00 pm
Location: Lower Hutt

Post by WACKO »

somone else on here has one... aparently goes quite well. if you buy tonys and come down to pick it up let us know.
User avatar
mytronic
Hard Yaka
Posts: 170
Joined: Tue Aug 22, 2006 12:00 pm
Location: Gisborne
Contact:

Post by mytronic »

Will do, I am very keen.
No top is the worring part for me. Street kids, rain ,CATS etc
User avatar
doddzee
Is Doddgee
Posts: 1211
Joined: Tue Oct 04, 2005 12:00 pm
Location: Warkworth, Auckland

Post by doddzee »

I think Tonys getting into Trials, Hence the sale.

ITs a good truck in mechanical condition as far as i know. Its only the dents that make it a look a bit rough but who wants a straight bush truck anyway.

A soft top isnt going to keep the street kids out either. :wink:
User avatar
mytronic
Hard Yaka
Posts: 170
Joined: Tue Aug 22, 2006 12:00 pm
Location: Gisborne
Contact:

Post by mytronic »

Thanks for the input doddzee

You are right, street kids and soft tops do not go together. On that note neither do beer bottles and back windows. Twice now !!

Good to hear that Tony's truck passes the peer test :wink:

My mechanic was OK with the M word also, whew :!: :!:

Don't suppose you have Tony's e-mail address do you?
User avatar
doddzee
Is Doddgee
Posts: 1211
Joined: Tue Oct 04, 2005 12:00 pm
Location: Warkworth, Auckland

Post by doddzee »

No i dont have his email sorry.

I had a 3.5 Pajero and i loved it, Never had any problems with it and the motor never made any noises it shouldnt have. The diesel pajeros have a bad reputation but you will be fine with a petrol.
User avatar
mudchuka
Hard Yaka
Posts: 271
Joined: Thu Feb 23, 2006 12:00 pm
Location: invercargill

Post by mudchuka »

iv just bought a 3.5v6 auto, 150 oookms $3500, they are getting very cheap to buy. we bought for a second car and for towing a trailer etc. how long do the transmissions last? am going to give it a full service, trans, fluids etc, pass on the cam belt, too pricey, it would be cheaper to let it go bang and buy a new truck!!!
Post Reply

Return to “Mitsubishi”